«MICROINCH»に関連する英語の本
以下の図書目録から
microinchの使いかたを見つけましょう。
microinchに関する本と英語文献で使われた文脈を提供するための簡単な抜粋文。
1
Engineering Drawing and Design
So if a surface roughness of 125 microinches is adequate, then do not use a 32-
microinch specification just because you like smooth surfaces. For example, note
the difference between 63- and 32- microinch finishes. A 63-microinch finish is a
...
2
Research and development study of a peristaltic action ...
This report investigates a peristaltic action microinch actuator for a primary mirror active-optics system of an orbiting astronomical telescope.
Carlo La Fiandra, Perkin-Elmer Corporation, Electronics Research Center (U.S.),
1970
3
Automotive Engines: Diagnosis, Repair, Rebuilding
Cylinders are honed with diamond, silicon carbide, or aluminum oxide stones of
a specified grit. The depth of the groove that a honing stone leaves in the surface
is measured in microinches. ○ One microinch equals one millionth of an inch.
4
Machine Trades Blueprint Reading
A microinch is one millionth of an inch. The higher the reading in microinches, the
rougher the surface finish. Microinch readings may be represented by the symbol
(fi in). Figure 25.6 shows typical applications and corresponding microinch ...
5
Microinch Machining of Optical Components for Infrared Optics
Single-point diamond knives have been used on precision lathes to machine to microinch tolerances.
T. T. Saito, AIR FORCE WEAPONS LAB KIRTLAND AFB N MEX.,
1974
6
A&P Powerplant Handbook AC 65-12A
The standard used when measuring the finish of a cylinder wall is known as
microinch root-mean- square, or microinch r.m.s. In a finish where the depth of
the grinding scratches are one-millionth (0.000001) of an inch deep, it is
specified as 1 ...
Federal Aviation Administration
7
Engineering Drawing and Design
For example, notice the difference between 63- and 32-microinch finishes. A 63-
microinch finish is a good machine finish that can be performed using sharp tools
at high speeds with extra fine feeds and cuts. Comparatively, the 32-microinch ...
8
Countersinking Handbook
... 1% 0.01 11% 0.08 11% 0.08 0.00024 26% 0.3 36% 1 2 Roughness Ra
roughness (microinch) 3 8 microinch 0.01 16 microinch 0.08 64 microinch 0.3
128 microinch 1.2 Chatter on metal surface Minimum magnification to clearly see
defect: 5 ...
9
Publications of the National Bureau of Standards ... catalog
Inertial guidance system gyroscopes and optical mirrors are designed to be
dimensionally stable to better than 1 microinch over long times. New gyroscope
designs require still better stability, 0.01 microinch. Uniaxial microcreep
experiments ...
United States. National Bureau of Standards,
1980
... 90-10 CuNi control 575 0.61 785 0.64 10 microinch parylene N on 80-10 CuNi
670 0.67 8S0 0.71 40 microinch parylene N on 00-10 CuNi 860 0.87 1,080 0.91
10 microinch parylene CR on 00-10 880 0.80 1.080 0.91 40 microinch parylene ...
用語«MICROINCH»を含むニュース項目
国内外の報道機関が語った内容や、次のニュース項目の文脈から
microinchという用語がどのように使われているかを調べてみましょう。
The Challenges of Measuring Microinches
When measuring to microinch tolerances, the gage should be protected from the operator's body heat and his breath by a clear plastic shield or full enclosure. «Modern Machine Shop, 7月 15»
Digital Indicators: Having it Your Way
It is not uncommon to find features such as dynamic measurements, multiple factors, unilateral tolerances, different output formats and microinch resolutions in ... «Modern Machine Shop, 6月 15»
Put Master Deviation to Use
Incorporating it into your master rings will boost measurement accuracy— an advantage in a manufacturing environment where every microinch counts. «Modern Machine Shop, 5月 15»
Untangling Some Confusing LVDT Terms
With a properly designed LVDT measuring system, microinch resolutions are not uncommon. Repeatability: The ability of a sensor to reproduce ... «Machine Design, 3月 15»
Standardized CNC Improves Production of Power-Generation …
Surface finishes typically range from 250 to 125 microinch Ra, though occasionally 64 or 32 microinch Ra is required. The finishes are achieved through both ... «Modern Machine Shop, 12月 14»
Cutting Tool Helps Automotive Manufacturer Implement Design …
Using Horn's Mini Mill, MT&G was able to produce a 15- to 20-microinch Ra finish without additional machining steps. Horn's Mini Mill enabled MT&G to take the ... «Modern Machine Shop, 11月 14»
Making Better Height Gage Measurements
If the base is six inches long, a 50 microinch error would grow to more than 0.0003 inch over a 36 inch height, and even more if the plate is out ... «Quality Magazine, 4月 14»
HMC Provides Quality Needed for Medical Manufacturing
The precision and rigidity of the a51 has enabled Big River to produce feature tolerances of ±0.01 to 0.03 mm with 32 microinch surface finishes or better. «Modern Machine Shop, 12月 13»
Laser Services and Inspection for Thin-Film Ceramic Substrates
The theoretical accuracy of this measurement is ± 1 microinch (± 25.4 micromillimeters). Hence there may be a difference in measurement from ... «Azom.com, 8月 13»
Panel-Mount USB Connectors include PCB solder tails.
The new connectors mount with standard 4-40 screws and use 30 microinch gold plated contacts to insure many mating cycles. "It is important ... «ThomasNet Industrial News Room, 11月 12»