10 ENGLISH BOOKS RELATING TO «FINGER TIGHT»
Discover the use of
finger tight in the following bibliographical selection. Books relating to
finger tight and brief extracts from same to provide context of its use in English literature.
1
Aviation Unit Maintenance Manual for Armament Subsystems, ...
Tighten nut finger-tight. Install T-bar guide (66) on forward housing and secure
with four bolts (59) and four washers (60). Tighten bolts finger-tight. Place stripper
sprocket assembly (64) in forward housing and secure with nut (53). Tighten nut ...
2
Aviation Maintenance Technician's Handbook
Self-sealing hose—if looser than finger-tight, tighten to finger-tight and add one-
fourth turn. [Table 7-4] Hose Clamps To ensure proper sealing of hose
connections and to prevent breaking hose clamps or damaging the hose, follow
the hose ...
3
101 Performance Projects for Your Pickup and SUV
Apply anti-seize to the £1 6-inch x 2^-inch socket head cap screw with £inch
washer and thread through water pump housing and into block only finger tight.
Thread the 2-Knnch-long spacer nut to the driver-side top stud and finger tighten.
4
Direct and General Support Maintenance Manual: Navigational ...
(6) Secure connector 1B1P1 with two jack- screws (1) by turning each jackscrew
a few turns clockwise until they are finger tight. (7) Install cover per subparagraph
e. g. Installation of Receiver 1RE1. (1) Note orientation of connector 1RE1P1 ...
Gripping with the little finger tight allows for a secure and flexible wrist because
when the little finger squeezes tight it allows the thumb to stay loose and flexible.
Having a squeeze the grip tightly by using the little fingers, but try not to be stiff at
...
Masao Takahashi, Ray Takahashi, June Takahashi, 2005
6
SPI/CI 52nd Annual Conference and Exposition 1997
The results for the seawater soaked and finger-tight cases are shown in Table III.
Again, in spite of the scatter in the failure loads of the same type of specimens,
the failure modes are the same for each specimen type. The last column shows ...
7
Composite Joints and Connections: Principles, Modelling and ...
Therefore, testing with finger-tight fasteners is usually considered conservative.
For quasi-static testing to failure, the reduction in strength is usually considered to
be due to the removal of friction forces for the finger-tight case (Wang et al., ...
8
Operator and Organizational Maintenance Manual: Tank, Steel, ...
Install nuts finger tight on the bolts. (11) Install center tension members (10) on
rafter posts (3 and 4). Insert bolts (16) through the members and posts. Install
nuts finger tight on the bolts. (12) Install outer tension members (12). Attach the 4-
bolt ...
to 74-88 foot-pounds if you are working on an Escort, Fiesta or Lynx. This is
equivalent to about IVfe turns after bolts are finger-tight. If you're working on an X-
body, tighten lower mounting bolts to 140 foot-pounds — about two turns after
bolts ...
10
Ultimate Boat Maintenance Projects
CO 03 Install the axle nut on the axle and tighten finger-tight, while turning the
hub. You want the bearings to be seated fully in the race. Make sure that you
installed the correct thrust washer under the nut. The correct washer will be big ...
10 NEWS ITEMS WHICH INCLUDE THE TERM «FINGER TIGHT»
Find out what the national and international press are talking about and how the term
finger tight is used in the context of the following news items.
Pickling and preserving summer's bounty
Apply lid, finger tight. Place jar in a dark, cool cupboard for two weeks, shaking every day to distribute salt. After two weeks, the lemons are ... «San Jose Mercury News, Jul 15»
Home Wrench: Six common beginner repair fails
When you re-tighten the little nut, finger tight to the point that it can't be depressed is all that's needed – anything more and you may damage its ... «BikeRadar.com, Jul 15»
Bike rodeo teaches safety
... sit two fingers above the eyebrow, with the Y shape of the strap framing each ear, and the chin strap should be one finger tight under the chin. «The Cold Lake Sun, Jun 15»
G2 Core 44 Axles Installed in Jeep JK Wrangler
Guide the stub shaft through the hub bore and thread the factory hub nut onto the stub shaft finger tight. Apply some anti-seize lube to the three ... «Four Wheeler Network, May 15»
Fixing Your Ford F-150 Power Steering Box
We installed the four bolts finger tight. Ford Power Steering Box Sector Shaft Cover Oring Installation Photo 111435899. We installed a new ... «Four Wheeler Network, May 15»
CD-R King affirms effort in helping clean environment through …
Simply slip this tool over the knob and give it 1/4 to 1/2 turn beyond finger tight and your LSF will be much harder to move while gliding or ... «Philippine Star, Apr 15»
Triptease: Seethi Betta and the finger offering
... amputations -- a goldsmith for cutting off the finger and others for dressing the wound and for holding the finger tight to stop the flow of blood. «Bangalore Mirror, Apr 15»
Trail Ready Jeep Grand Cherokee WJ Front Bumper Install
We only installed it finger tight at first. ... flat washer and lock washer are secured finger tight so the bumper can be properly positioned. «Off-Road.com, Jan 15»
DIYtyre changing tips
Thread the lug nuts back on until they're finger tight, working in a star shape, then tighten with the wrench until they are just firm. DIY Changing ... «CarAdvice, Nov 14»
Grieving Chester parents raise funds for Ronald McDonald House
... Dance, which was his favourite - every time I read it to him he opened his eyes and held my finger tight and he improved,” said Rebecca. «ChesterChronicle.co.uk, Oct 14»
