CĂRȚI ÎN ENGLEZĂ ÎN LEGĂTURĂ CU «ORTHOTROPY»
Descoperă întrebuințarea
orthotropy în următoarea selecție bibliografică. Cărți în legătură cu
orthotropy și extrase din aceasta pentru a furniza contextul de întrebuințare al acestuia în literatura Engleză.
1
Turbomachinery Rotordynamics: Phenomena, Modeling, and Analysis
(d) Orthotropy can be introduced in the bearing-support stiffness, keeping in mind
that this may yield a broader speed range of larger-amplitude synchronous
response and may occasionally provide a mechanism for exciting asynchronous
...
2
Delaware Composites Design Encyc: Micromechanical Materials ...
Subsection 2.2.1 considers the stress-strain relations in cylindrical coordinates,
using engineering constants (Young's modulus, shear modulus, Poisson's ratio).
The equations for the special case of transverse orthotropy in the r-6 plane are ...
University of Delawa, 1990
3
Scaling of Structural Strength
Effect of Material Orthotropy In the case of fiber composites, as well as some
rocks, LEFM must be generalized to take into account the orthotropy of the
material. The stress intensity factor of a sharp crack with a negligibly small FPZ
may always ...
A special case of anisotropy in which the material properties are different in two
mutually perpendicular directions is called orthogonal anisotropy or orthotropy. In
this chapter we will discuss plate bending problems in which the plate material ...
5
Plastic Limit Analysis of Plates, Shells and Disks
Stiffeners are most often placed along the lines of an orthogonal net and the plate
so constructed exhibits structural plane orthotropy, that is, stmctural plane
anisotropy with two orthogonal axes of symmetry. Material orthotropy can also
arise ...
M.A. Save, C.E. Massonnet, G. de Saxcé, 1997
6
Vibration of Laminated Shells and Plates
5.1.4 Equations of thin plates with rectangular orthotropy Unlike homogeneous
plates, where the coordinates are chosen solely based on the plate shape,
coordinates for laminated plates should be chosen carefully. There are two main
factors ...
7
Geometrically Exact Theory for Contact Interactions
Constant orthotropy is thoroughly investigated for the case with small
displacements in order to show the development and the distribution of the
sticking-sliding zone for different types of orthotropy. These cases are considered
for the start of ...
Alexander Konyukhov, 2010
8
Plates and FEM: Surprises and Pitfalls
There is a large difference between isotropy and orthotropy, however not
between classical orthotropy and advanced orthotropy. Therefore, just the
advanced results are shown. Figure 18.10 shows distributions of the membrane
force and ...
Johan Blaauwendraad, 2010
9
ECCM-8 European Conference on Composite Materials: Science, ...
In this study the test quality was analysed with respect to the influence of the
material orientation, the ratio of orthotropy and the degree of heterogeneity of the
tested material. The numerical model was built with the finite element software ...
I. Crivelli Visconti, 1998
10
Design, Fabrication and Economy of Welded Structures: ...
Keywords: Orthotropy, elastic constants, FEA 1 Introduction Laser welded
structural steel sandwich panels; see Figure 1, that are now available on the
market offer strong and lightweight materials for heavy industries. They usually
enable 20 to ...
Károly Jármai, József Farkas, 2008
ȘTIRI NOI CARE INCLUD TERMENUL «ORTHOTROPY»
Află ce ziare naționale și internaționale au scris despre și cum este întrebuințat termenul
orthotropy în contextul următoarelor știri.
Compact tension fracture toughness testing
Correspondingly, the compact tension specimen is used to test some types of composite materials that have limited orthotropy, including ... «High Performance Composites, Iul 14»
Buckling of composite material compression specimens
... materials but subsequently modified to account for the influence of material orthotropy. This modified equation to predict the buckling stress, ... «High Performance Composites, Ian 14»
Sensing the Human Body: Hearing Control using an Electronic …
The results also concluded that the obtained orthotropy ratio is not enough to achieve sharp filtering produced in computational models and ... «AZoSensors, Ian 13»
Tabbing composite test specimens: When and why
How short is guided by the Euler buckling equation, modified to account for material orthotropy.1 For specimens of typical thicknesses (3 ... «High Performance Composites, Mar 11»
