КНИГИ НА АНГЛИЙСКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «BEVEL GEAR»
Поиск случаев использования слова
bevel gear в следующих библиографических источниках. Книги, относящиеся к слову
bevel gear, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на английский языке.
1
Gear Geometry and Applied Theory
Reduction of noise and stabilization of bearing contact of misaligned spiral bevel
gear drives are still very challenging topics of research although manufacturing
companies [Gleason Works (USA), Klingelnberg-Oerlikon (Germany- ...
Faydor L. Litvin, Alfonso Fuentes, 2004
2
Handbook of
Gear Design
As stated before, the pitch surface of a bevel gear is a (truncated) cone. When
two bevel gears mate, their respective pitch cones contact along a common
element. The pitch cones, when extended, meet at a common point called the
apex.
3
Handbook of Practical
Gear Design
Bevel gear blanks are conical in shape. The teeth are tapered in both tooth
thickness and tooth height. At one end the tooth is large, while at the other end it
is small. The tooth dimensions are usually specified for the large end of the tooth.
Stephen P. Radzevich, Darle W. Dudley, 1994
4
Handbook of Case Histories in Failure Analysis
Stripping of the engine revealed that the bevel gear locating splines (16 NCD 13)
had failed. Visual and low-power microscopy examination of the spline of the
shaft showed evidence of fretting wear debris; similar wear was observed on the
...
Khlefa Alarbe Esaklul, 1992
5
Gear Design Simplified: A Series of
Gear-designing Charts ...
24 worm and worm-gear ..103, 104 Change-gear ratio for cutting diametral pitch
worms _ ..104 Chordal addendum, large end of bevel-gear tooth 45 rules and
formulas for spur gear ..-.. 25, 27 small end of bevel-gear tooth 44 spiral-bevel ...
Franklin Day Jones, Henry H. Ryffel, 1961
6
DESIGN OF MACHINE ELEMENTS
The dynamic load on a bevel gear tooth is caused due to profile error of the tooth,
which can be computed on the lines of the spur gear except that the velocity at
the largest pitch circle must be computed and tangential force should then be ...
KAMLESH PUROHIT, C. S. SHARMA, 2002
7
Dudley's Handbook of Practical
Gear Design and Manufacture, ...
However,.in.calculating. bearing.loads,.central-section.dimensions.and.forces.
are.used. The.simplest.type.of.bevel.gear.is.the.straight.bevel.gear..These.gears.
are.commonly.used. for.transmitting.power.between.intersecting.shafts.
Stephen P. Radzevich, 2012
8
Automotive Transmissions: Fundamentals, Selection, Design ...
This book gives a full account of the development process for automotive transmissions.
Aaron Kuchle, Harald Naunheimer, Bernd Bertsche, 2010
9
DS, GS, and Depot Maintenance Manual: Tractor, Full Tracked, ...
4 5 To remove bevel gear and shaft proceed as follows: (1) Remove drain plugs
from bevel gear compartment, and both steering clutch compartments and allow
oil to drain. Refer to paragraph 131 and remove steering clutches and steering ...
10
Direct support, general support, and depot maintenance ...
T 7 I III BEVEL GEAR AND SHAFT REMOVAL 1-Bearing cages. 2-Bevel gear
shaft. 3-Bevel gear. NOTE When removing bearing cages (1), keep the shims
with each related bearing cage and mark the cages to assure installation in their
same ...
United States. Dept. of the Army, 1991
НОВОСТИ, В КОТОРЫХ ВСТРЕЧАЕТСЯ ТЕРМИН «BEVEL GEAR»
Здесь показано, как национальная и международная пресса использует термин
bevel gear в контексте приведенных ниже новостных статей.
Autodesk Patent Reveals Several Advanced Multi-Color FDM 3D …
Roller 3042 rolls off of the currently engaged bevel gear 3028, which then disengages from transfer gear 3046. Roller 3042 then rolls onto the ... «3DPrint.com, Июн 15»
Ning and Stadtfeld named Inventors of the Year
He is vice president of bevel gear technology and R&D for Gleason. Ning developed a system that gives a more precise view of breast tissue ... «Rochester Democrat and Chronicle, Июн 15»
Vertical axis set to shake up wind turbine market
The turbine has a helical bevel gear unit at its base and the IE3 rated motor is close coupled with the gearbox. The shaft is supported by ... «E&T magazine, Май 15»
Innovation drives Rochester
... saves energy and materials as well as making a safer work environment. He is vice president of bevel gear technology and R&D for Gleason. «Rochester Democrat and Chronicle, Май 15»
Vertical turbine design now reality
The 4Navitas VAWT also houses a Siemens FZG helical bevel gear unit at its base. The power from the wind is controlled by a Siemens ... «reNews, Май 15»
TECHNICAL ANALYSIS: Ducati's 821 Testastretta Engine We've …
... Taglioni extensively drew from the experience collected in years of honing the 250cc Desmo and the mighty 750/900 90-degree “bevel gear” ... «Cycleworld, Май 15»
Harley-Davidson Project LiveWire: PH2 review
It has actually engineered a whine (Harley claims it sounds like a jet fighter) into the bike using a bevel gear on the electric motor's drive. «Pistonheads.com, Май 15»
Lifting system from Pfaff-silberblau for flood protection gate in the …
... trapezoidal screw, special travelling nut, absolute encoder, special grease and a bevel gear box motor with 1.5 kW actuating power is used. «presseagentur.com, Май 15»
Bevel Gear Grinder Speeds Setup
The Phoenix 280G bevel gear grinding machine from Gleason is designed for high productivity and reliability in grinding bevel gears ranging to 280 mm in ... «Modern Machine Shop, Май 15»
Polyketone makes grade for new high-performance, wear-resistant …
... bevel gears, gear racks, sprocket wheels, small bevel-gear systems, and planetary gears, typically made from polyamide (PA) and polyacetal ... «Plastics Today, Май 15»
