КНИГИ НА АНГЛИЙСКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «MODULUS OF RIGIDITY»
Поиск случаев использования слова
modulus of rigidity в следующих библиографических источниках. Книги, относящиеся к слову
modulus of rigidity, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на английский языке.
1
Specifications for Structural Concrete, ACI 301-05, with ...
modulus of resilience—see resilience. modulus of rigidity—the ratio of unit
shearing stress to the corresponding unit shearing strain; referred to as shear
modulus and modulus of elasticity in shear, denoted by the symbol G. (See also
modulus ...
American Concrete Institute, 2005
2
The Strength
of Materials
Measurement of the Modulus of Rigidity. Static Method. This modulus is usually
measured by experiments on the torsion of a round rod or wire. It will be shown
later that when such a rod is twisted every part of it is in a state of shear, and that
...
3
A Textbook
of Strength
of Materials
[Ans. (i) 1.989 x 105 N/mm2, (ii) 0.234, (iii) 1.2465 x 105 N/mm2] Determine the
Poisson's ratio and bulk modulus of a material, for which Young' s modulus is 1.2
x 105 N/mm2 and modulus of rigidity is 4.5 x 104 N/mm2. [Ans. 0.33, 1.2 x 105 ...
4
Titanium: A Technical Guide
Specifically, the modulus obtained in tension or compression is Young's modulus
(E), stretch modulus, or modulus of extensibility; the modulus obtained in torsion
or shear is modulus of rigidity, shear modulus (G), or modulus of torsion; the ...
Matthew J. Donachie, 2000
5
Mechanics
Of Materials (In Si Units)
... is applied at end A of the composite shaft shown. Knowing that the modulus of
rigidity is 77 GPa for the steel and 27 GPa for the aluminum, determine (a) the
maximum shearing stress in the steel core, (b) the maximum shearing stress in
the ...
Beer, Johnston & Dewolf, 2004
6
Significance
of Tests and Properties
of Concrete and ...
The dynamic modulus of rigidity is about 40 % of the modulus of elasticity [14]. It
should be mentioned that more input energy is needed for longitudinal
resonance and, therefore, the transverse resonance mode is used more often in
laboratory ...
Joseph F. Lamond, J. H. Pielert, 2006
7
Reinforced Masonry Engineering Handbook: Clay and Concrete ...
These coefficients are based on a modulus of elasticity, Em, of 1,000,000 psi, a
modulus of rigidity, G (or Ev) of 0.4 Em = 400,000 psi, a 1 inch wall thickness and
a lateral force of 100,000 pounds. To obtain deflection or rigidity coefficients for ...
8
DESIGN
OF MACHINE ELEMENTS
In order to perform design, the user is expected to furnish the following input
details: (i) maximum force, (ii) deflection, (iii) selection of material, (iv) modulus of
rigidity, (v) factor of safety, and (vi) spring index. In this program, square and
ground ...
KAMLESH PUROHIT, C. S. SHARMA, 2002
9
Competition Science Vision
The stress at which the rupture occurs in the material is called 'breaking stress'.
Types of Modulus of Elasticity (1) Young's modulus of elasticity (Y) (2) Bulk
modulus of elasticity (K) (3) Modulus of rigidity (η) (1) Young's modulus of
elasticity (Y) ...
10
Mechanical Experiments and Workshop Practice
OBJECTIVE To ascertain the modulus of rigidity of a rod by statical method using
horizontal pattern of torsion test apparatus (clamp pattern type). 2. THEORY A
torsion test apparatus is used in determining the value of the modulus of rigidity
of ...
НОВОСТИ, В КОТОРЫХ ВСТРЕЧАЕТСЯ ТЕРМИН «MODULUS OF RIGIDITY»
Здесь показано, как национальная и международная пресса использует термин
modulus of rigidity в контексте приведенных ниже новостных статей.
Samsung profits decline as other OEMs eat its lunch
I thought that higher numbers for Modulus of Rigidity (or Shear Modulus) were indicative of greater rigidity. Polycarbonate shows up at 2.3GPa ... «ExtremeTech, Июл 14»
Car manufacturing – fast track towards mass production
Through the modulus of rigidity, the researchers simulate how rigid the device would be if it were made of steel, aluminum or synthetic material. «Phys.Org, Янв 14»
ADMET Introduces Torsion Testing Machines
Both controllers offer calculation of key test parameters, such as ultimate shear strength, yield shear strength, Modulus of Rigidity, Modulus of ... «PR Web, Май 09»
