ЧТО ОЗНАЧАЕТ СЛОВО OFFCUT
Значение слова offcut в словаре английский языка
Определение обрезания в словаре - это лист бумаги, фанера, ткань и т. Д., Оставшиеся после вырезания основных предметов; остаток.
КНИГИ НА АНГЛИЙСКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «OFFCUT»
Поиск случаев использования слова
offcut в следующих библиографических источниках. Книги, относящиеся к слову
offcut, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на английский языке.
1
Castle Park, Dunbar: Two Thousand Years on a Fortified Headland
Offcut. Length 39mm; width 4mm; thickness 2mm Offcut with one knife-trimmed
edge. (Not illustrated) Context 0215; Find No 00216; Phase 14 141. Offcut.
Length 34mm; width 16mm; thickness 5mm Offcut with knife-trimmed edges,
folded ...
David R. Perry, Mark A. S. Blackburn,
2000
2
The Science and Engineering of Cutting: The Mechanics and ...
When permanent deformation of the offcut occurs, as with tinsnips or devices for
clipping coins (in the USA, two bits one quarter), the analysis of the next section
is required. 5.4.3 Ductile materials The cut edges of guillotined plates of ductile ...
3
Carving as Craft: Palatine East and the Greco-Roman Bone and ...
Offcut. D98:IV/3687 (PI. 1ib) D.0.050; L.0.037; W.0.035; Th.0.004. Broken at both
ends. Fragment of long bone from which disk was cut. Bottom edge incompletely
turned. St. Clair 1996, 371, Fig. 14. LATE FIRST TO EARLY SECOND ...
4
A Dictionary of the Art of Printing
The oflFcut is now to be considered — this is always imposed on the outside of
the short cross, and the back and gutters are the same as those in the other part
of the sheet ; for the head of the offcut, the space between the running title, or, ...
5
Woodworking Techniques: Best Methods for Building Furniture ...
A safety warning: This method of cutting miters leaves room for the offcut to drift
away from the blade, but it doesn't guarantee against potentially dangerous
kickback. Never try to pull the offcut through when the saw is running. Do not
stand ...
6
Defect Structures and Growth Mechanisms of Boron Arsenide ...
In addition, the application of offcut can significantly narrow the area of each
terrace and thus may limit the number of possible structural variants. Thus the
use of offcut substrates potentially enables manipulation of the relative
populations of ...
7
Microscopy of Semiconducting Materials 2003
The diffuse lines lie roughly parallel to <100>, i.e. parallel to the steps on the
substrate surface produced by the 2° offcut. However, for monatomic height steps
on the semiconductor surface, the terrace width on a 2° offcut substrate is 8.1 nm,
...
A.G Cullis, P.A. Midgley,
2004
8
Silicon Photonics for Telecommunications and Biomedicine
There is therefore a growing concern whether offcut Si substrates are suitable for
the mainstream Si electronics. Preliminary studies have been performed to
compare the characteristics of metal-oxide-semiconductor field-effect transistor ...
Sasan Fathpour, Bahram Jalali,
2011
9
Zirconium in the Nuclear Industry: Ninth International Symposium
not beta-quenched during fabrication; A ^ also examined after heat treatment of
24 hours at 560°C. Section = section from removed pressure tube; offcut =
section cut off front or back of pressure tube; hid ring hardness ring. 'End of
pressure ...
Craig M. Eucken, A. M. Garde,
1991
10
Manual of First and Second Fixing Carpentry
Figures 12.33(g) and (h): An interesting variation on the above method is to omit
the rafter offcut which equalled two-thirds' ... rest the length of hip rafter on the
actual diagonally offcut wall-plate edge instead (Figure 12.33(h)), and again on
the ...
НОВОСТИ, В КОТОРЫХ ВСТРЕЧАЕТСЯ ТЕРМИН «OFFCUT»
Здесь показано, как национальная и международная пресса использует термин
offcut в контексте приведенных ниже новостных статей.
Meet the maker: Furniture maker, sculptor and musician Sime Nugent
His dad still has Nugent's first found object sculpture, made at the age of five from an offcut of framing pine discarded in a laneway. Drilling ... «Sydney Morning Herald, Июл 15»
VicForests considers exporting residual/offcut timber to China
What should be done with Victoria's low grade native timber.... or what's called residual timber? Should it be wood-chipped, maybe burnt for ... «ABC Online, Июл 15»
16 brilliant songs of 2015 you may not have heard
Flying Lotus - 'Eyes Above' ft Kendrick Lamar: Released as a part of Flying Lotus' Radio 1 residency, Eyes Above ft K.Dot was an offcut from ... «Gigwise, Июл 15»
Vet Center offers retreat, free help without red tape
Offcut and Pierce have a firsthand knowledge of what that's like. ... their bitterness because they want to help these younger vets," Offcut said. «mySanAntonio.com, Июл 15»
Made in London: House of Sverre's luxury smoked salmon
Offcut: House of Sverre's smoked salmon pate What's it like running a business in London? It's even easier than in Sweden. It's less controlled ... «Evening Standard, Июл 15»
Grading gallium indium nitride arsenide for multi-junction solar cells
The substrates were zinc-doped (100) GaAs wafers offcut 6° to the (111)B plane. Layers of Ga1-xInxNyAs1-y were grown at 380°C. Different ... «Semiconductor Today, Июл 15»
Vet Center offers warm, welcoming retreat, free help without red tape
Offcut and Pierce have a firsthand knowledge of what that's like. ... their bitterness because they want to help these younger vets," Offcut said. «Las Cruces Sun-News, Июн 15»
She's Funny That Way review – rom but no com
Despite taking its “squirrels to the nuts” cue from Ernst Lubitsch, this plays more like an unmemorable late-period Woody Allen offcut, its parade ... «The Guardian, Июн 15»
Creating n-InP/p-Si heterojunctions with lateral overgrowth
KTH used (001) p-Si substrates offcut 4° in the <111> direction. The processing began with metal-organic vapor phase epitaxy (MOVPE) of ... «Semiconductor Today, Июн 15»
Pork belly demand puts it a cut above the rest
Mitch Edwards, marketing manager from Australian Pork Ltd, points the finger of pork belly's rise from butcher shop offcut to culinary superstar ... «Good Food, Июн 15»