КНИГИ НА АНГЛИЙСКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «OVALITY»
Поиск случаев использования слова
ovality в следующих библиографических источниках. Книги, относящиеся к слову
ovality, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на английский языке.
1
Thin-Walled Structures: Advances in Research, Design and ...
bulging process should cease once the ovality and angular distortion of the
polyhedron are all equal to the largest values specified in the relevant spherical
pressure vessel standard. Obviously, if the ovality and angular distortion during ...
2
Heavy Duty Truck Systems
When checking for runout, it is important to distinguish between runout and
ovality. Runout occurs when a drive shaft tube is slightly bent but still maintains
its circularity throughout the tube. When you measure runout, the indicator needle
will ...
3
Handbook of Analysis and Quality Control for Fruit and ...
S. Ranganna. Pillar ial indicator Hardened piece Base plate Half of the total
deflection shown by the indicator is the variation in the verticality of the bottle. The
verticality tested by the above method should not vary more than 2.5 mm. Ovality
...
4
Handbook of Surface and Nanometrology
1 9 Assessment of ovality and other shapes Ovality is the expected basic shape
in workpieces generated from round stock rolled between two rollers. It is one of
the commonest faults in rings such as ball races. It is, however, different from ...
David J. Whitehouse, 2002
5
Heat Treating: Including Advances in Surface Engineering, an ...
Here, again, the complete system should be considered. It does not make sense
to reduce cost during soft machining to a certain extent, if this measure increases
cost for hard machining due to excessive distortion. ("Ovality range Spread in ...
Kiyoshi Funatani, George E. Totten, 2001
6
Thermal Deformations of Thin-Walled Planetary Gears
Table 7 Evaluation of forming ring (type II)* for the different treatments at
conditions when primary ovality is equal zero , i.e 8°h=8°b=0 * material-
chromium steels; all sizes are in millimeters From Figure 2 1 we see that ovality of
external and ...
7
Defect Prevention: Use of Simple Statistical Tools
Figure 1 2.46 Gear ID and OD. rework and poor tool life. However, there was
minimal ovality (defined as the maximum ID size minus the minimum ID size for
this study) in the ID prior to heat treat. Several before and after heat treat studies
were ...
8
Advances n Mechanical Engineering
D. S. Ramakrishna, K. Sabeel Ahmed, C. D. Ashok Kumar, Jawaharlal Nehru
National College of Engineering. Table 3: Main Effects and Their Differences on
Ovality Table 4: ANOVA Table Design and Development of CAM Actuated. The
main ...
D. S. Ramakrishna, K. Sabeel Ahmed, C. D. Ashok Kumar, 2010
9
Pistons and engine testing
2.2.2. Ovality. Pistons typically have a slightly smaller diameter in the piston pin
axis than in the thrustantithrust axis. The difference is the (diametric) ovality;
Figure 2.5. The oval shape of the crown and skirt provides many design
opportunities.
10
Heat Treating 1998: Proceedings of the 18th Conference: ...
Work by G. Wahl(29), showed that increasing the temperature of quenching oil
from 60°C to 110°C, reduce ovality in bearing rings. Using salt at a higher
temperature, 160°C, produced a further small improvement in ovality but further ...
НОВОСТИ, В КОТОРЫХ ВСТРЕЧАЕТСЯ ТЕРМИН «OVALITY»
Здесь показано, как национальная и международная пресса использует термин
ovality в контексте приведенных ниже новостных статей.
Triptech Plastics Announces Unmatched Resin for 3D Printing and …
Filament made with Amphora offers 3D printers higher tensile strength, truer ovality and dimensional integrity. Triptech Plastics has special ... «Robotics Tomorrow, Июл 15»
EXTRUSION AND COMPOUNDING AT NPE: Flexibility, Speed …
(0.1524-mm) diameter variation and less than 0.001-in. (0.305-mm) variation in ovality of the filament. Conair designed the GRH-1.0 extrusion die specifically for ... «Plastics Technology, Май 15»
Lumetrics Obtains Patent for Contact Lens Measurement System
... Food Packaging, and more; Measure Layer Thickness, Wall Thickness, Diameter, Concentricity, and Ovality; Measurements from sub-micron ... «PR Web, Май 15»
Hidden Factors in Measurements
A number of readings taken along and around the pin may show ovality or two-point lobing but not three or five lobed roundness variations. «Quality Magazine, Мар 15»
battenfeld-cincinnati USA: Continued Success
... and offers an extensive range of pipe heads that achieve optimal wall thickness distribution, ovality and low sagging thanks to the proprietary ... «Packaging Europe, Мар 15»
Auxiliary equipment makers seek to improve processing
Beta LaserMike (Booth W2991): AccuScan 6012 and 5000 series diameter and ovality four- and two-axis gauges; LN3040 lump and neckdown ... «Plastics News, Мар 15»
Klipsch KG-300 Gaming Headset Review
If nothing else, I applaud its defiant, cool character in a crowd abundant with ovality. Sadly, it's hard to give applause to it for comfort. Not only ... «Gameranx, Фев 15»
Welltec® Annular Barrier Installed in First Presalt Deepwater Well for …
... allow it to be expanded from surface, with no waiting times and conform to the surrounding open hole environment, even if ovality is present. «PR Newswire, Фев 15»
Cup-seal packer enhances sand control in open-hole wells
The packer can be set without intervention or hydraulically in a variety of environments, achieving up to 1.2 ovality. In addition to zonal isolation, ... «Offshore Oil and Gas Magazine, Янв 15»
Tech Roundup: Featuring Rapha, Zipp, Rotor...
“Their design features include subtle but efficient ovality and adjustability to ensure minimum diameter related to the start of pedal stroke and ... «road.cc, Янв 15»
