КНИГИ НА АНГЛИЙСКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «STICKOUT»
Поиск случаев использования слова
stickout в следующих библиографических источниках. Книги, относящиеся к слову
stickout, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на английский языке.
As can be seen from equation (10.3), a voltage drop occurs in the electrode
stickout. Hence higher length of stickout will offer higher electrical resistance and
will cause a higher voltage drop. This higher resistance will also cause a
resistance ...
2
Advanced Automotive Welding
This table presents some results of stickout change on melting rate and penetra-
tion. It assumes the wire feed speed remained constant. As stickout increases,
amperage reduces, which causes weld penetration to in this figure, the wire-feed
...
Gerald Uttrachi, Jerry Uttrachi, 2012
The amount of stickout can vary depending on the wirefeed process: • Short-
circuit transfer; stickout of lA to Vi inch is used — %-inch stickout is ideal. • Spray,
pulse spray, and FCAW-G; stickout of Vs inch minimum to 3A inch maximum.
4
Handbook of Industrial Robotics
POSTFLOW TIME: 13. WEAVE WIDTH: 14. LEFT DWELL: 15. RIGHT DWELL: 16.
CROSS TIME: 17. STICKOUT CURRENT: 18. TRAVEL SPEED: voltage required
for burnback. provides extra shielding gas to insure coverage of the crater as it ...
5
Welding for Challenging Environments: Proceedings of the ...
Feedback loops present differing effects on overall performance in terms of heat
input, penetration, and puddle control. TOO LONG TOO SHORT 1,2552%“. :14“
stickout 1M" stickout Average emperes 185 150 115 Average volts 20 20 20 Wire
...
Welding Institute of Canada, 1986
With a long stickout the wire becomes soft from resistance heating and the end
tends to wander either under the magnetic force of the arc or the natural cast of
the wire. As exact alignment of the arc is important in submerged-arc welding, it is
...
7
Fundamentals of Machine Elements, Third Edition
Such bearings are usually preloaded against each other by providing what is
called stickout in the manufacture of the bearing. Figure 13.17 illustrates stickout
for a bearing pair used in a back-to-back arrangement. The magnitude of the ...
Steven R. Schmid, Bernard J. Hamrock, Bo. O. Jacobson, 2013
Manufacturers provide guidance on the appropriate stickout to use and in
downhand fillet welding with gas-shielded wires this is likely to be in the range 20
—30 mm. Shortening the stickout increases the penetration and reduces the
convexity ...
9
Weld Integrity and Performance: A Source Book Adapted from ...
Pores in passes 3,4,6, and 8 were caused by intentionally varying the electrode
stickout. present in the sectioning plane are visible. In this example, nine passes
were made, three layers with one pass and three with two passes. Figure 8 also ...
Steve Lampman, ASM International, 1997
10
Principles of industrial welding: a text for students and ...
The procedures for self-shielded flux-cored arc welding specify electrical stickout
along with electrode type and diameter and current and voltage ranges. Thus, the
procedures for a typical 1/8-in. E70T-4 electrode wire may prescribe a current ...
Harry Honegger, James F. Lincoln Arc Welding Foundation, Enrico P. Bongio, 1978
НОВОСТИ, В КОТОРЫХ ВСТРЕЧАЕТСЯ ТЕРМИН «STICKOUT»
Здесь показано, как национальная и международная пресса использует термин
stickout в контексте приведенных ниже новостных статей.
The smart way to pimp your ride - with StickOut
Ready to pimp your ride – with computer generated designs? If so, Tel Aviv-based startup StickOut, which launched a crowdfunding campaign today on ... «Geektime, Май 15»
