КНИГИ НА АНГЛИЙСКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «TOOLHOLDER»
Поиск случаев использования слова
toolholder в следующих библиографических источниках. Книги, относящиеся к слову
toolholder, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на английский языке.
1
Metal Cutting Theory and Practice
TABLE 5.1 9 Comparison of Tool-Toolholder Connections Using a 1 9 mm
Diameter Steel Rod With 50 mm Overhang on Standard 40 Taper Toolholder
Based on Dynamic Tests [46] Toolholder System Modes Frequency (Hz) Stiffness
(N/mm) ...
David A. Stephenson, John S. Agapiou, 2005
2
SPE/ANTEC 1999 Proceedings
Abstract High Speed Milling requires many considerations for the toolholder.
Cleanliness, Balance and Accuracy become even more important as the spindle
RPM rises. With milling speeds rising through ten, thirty, and fifty thousand RPM,
...
3
AMST'05 Advanced Manufacturing Systems and Technology: ...
To obtain a good compromise between sensitivity to the torque and cutting
performance, an accurate structural analysis on the modified toolholder has been
performed. In Fig. 2 and Fig. 3 the commercial toolholder and the modified
toolholder ...
4
Precision Machining Technology
The fifth position in Figure 5.3.22 identifies the hand of the tool. The toolholder
positions the insert to make the desired direction of cut possible. As mentioned
earlier in the unit, a right-hand tool cuts from right to left, a left hand tool cuts from
left ...
Peter Hoffman, Eric Hopewell, Brian Janes, 2014
5
Machining of Hard Materials
This sensitivity to impurities requires extreme care during tool changes, and the
usual solution is to inject pressurized air into the spindle nose and the holder
before each tool change. 2.7.2.2 Other Toolholder Systems There are other types
of ...
6
Stiffness and Damping in Mechanical Design
The absence of face contact between toolholder and spindle leads also to
micromotions between the male and female tapers within the radial clearance
under heavy cutting forces, leading to accelerated wear of the front part of the
spindle ...
7
Adjustable
toolholder for your Unimat
YOU CAN INCREASE the versatility of your American Edelstaal Unimat by
customizing a toolholder so that the height of the cutting end of the tool bit can be
adjusted up or down. Though the toolholder shown does just that, it does not
totally ...
8
Machine Tools for High Performance Machining
The CAT toolholder was created by the Caterpillar Corporation in order to
standardise the tool holding systems in their machine tools. These holders are
designed according to the size of the cones and are classified as CAT-30, CAT-
40 and ...
Norberto Lopez de Lacalle, Aitzol Lamikiz Mentxaka, 2008
9
Principles of Process Planning: A Logical Approach
The absence of a protruding top clamp provides unhampered chip flow. It is a low
cost and quick change and indexing operation. The design allows the use of a
shorter toolholder. The second digit The second digit represents the insert shape.
G. Halevi, R. Weill, 1995
10
Principles of Engineering Manufacture
V. Chiles, S. Black, A. Lissaman, S. Martin. 11.3 The selection process The
application of turning tools can be carried out according to the following stepby-
step approach. . Edge clamping system. . Toolholder size and type. . Insert shape
.
V. Chiles, S. Black, A. Lissaman, 1996
НОВОСТИ, В КОТОРЫХ ВСТРЕЧАЕТСЯ ТЕРМИН «TOOLHOLDER»
Здесь показано, как национальная и международная пресса использует термин
toolholder в контексте приведенных ниже новостных статей.
Rigid polygon shank toolholder series provides high bending and …
This results in hardened shank and insert seating that will then extend the life of the toolholder, the company says. The series includes general turning, copying, ... «ETMM Online, Июл 15»
SCHUNK TENDO-Series Toolholders
There are three versions of TENDO toolholders, namely the TENDO-E compact hydraulic toolholder, TENDO-Tech toolholder, and the TENDO-Platinum ... «Azom.com, Июл 15»
EXSYS offers thread whirl toolholder
San Antonio, Florida – Designed for single-spindle Swiss screw machines, the latest thread whirling toolholder from Exsys Tool Inc. productively machines ... «Aerospace Manufacturing and Design, Май 15»
EXSYS thread whirl toolholder
The ring-shaped toolholder has an adjustable range of 0 and 15° to accommodate most profile shapes. It employs a maximum input and output rpm of 6,000 ... «Today's Medical Developments, Май 15»
EXSYS Tool introduces a thread whirling toolholder
EXSYS Tool is introducing its latest thread whirling toolholder designed for single-spindle Swiss screw machines to machines high-precision OD threads in ... «Canadian Metalworking, Апр 15»
Toolholder trouble
Want to avoid toolholder trouble? The first step is recognizing the importance of toolholders in the manufacturing process. While toolholders are the vital link ... «Canadian Metalworking, Мар 15»
Hydraulic Expansion Toolholder suits aerospace applications.
SCHUNK is broadening its program for high performance hydraulic expansion toolholders with the TENDO AVIATION. This toolholder specifically focuses on ... «ThomasNet News, Мар 15»
SCHUNK's TRIBOS-RM toolholder
SCHUNK has announced its toolholder that offers special consideration must be made for micro-machining. SCHUNK is offering the TRIBOS-RM precision ... «Canadian Metalworking, Дек 14»
Ultrasonic-Assisted Machining with Standard Machines and Tools
A system to be marketed in 2015 will apply ultrasonic vibration from within the toolholder to reduce cutting force and improve the performance of the cut. «Modern Machine Shop, Авг 14»
Coolant-Through Toolholder Clamps for CNC Swiss-Type Lathes
GenSwiss introduces its Multidec-Lube coolant-through toolholder clamp for CNC Swiss-type lathes, which supports optimum coolant jet positioning. «Modern Machine Shop, Июл 14»
