КНИГИ НА ТУРЕЦКИЙ ЯЗЫКЕ, ИМЕЮЩЕЕ ОТНОШЕНИЕ К СЛОВУ «DUROMER PLÂSTIK»
Поиск случаев использования слова
duromer plâstik в следующих библиографических источниках. Книги, относящиеся к слову
duromer plâstik, и краткие выдержки из этих книг для получения представления о контексте использования этого слова в литературе на турецкий языке.
1
Corrosion-Resistant Plastic Composites in Chemical Plant ... - Sayfa 172
Some epoxy manufacturers recommend the use of a gasket material in the 40-50 durometer range. Many engineers prefer a 70 durometer in preference to a 40 durometer gasket because the 40 durometer gasket will tend to deform and ...
2
Handbook of Materials Selection - Sayfa 568
Durometer Hardness (ASTM D2240, ISO 868) The Durometer hardness test is mostly used for measuring the relative ... 2 THERMAL PROPERTIES Thermal properties of plastic materials are equally as important as mechanical properties.
3
Report of the Meeting [Plastic Study Group] - Sayfa 84
The gasket may be any one of the synthetic rubbers, but it should possess as low a durometer rating as is consistent ... It is a plastic. This sealing material should have a proper viscosity and durometer rating so that it will not become too rigid.
National Research Council (U.S.). Building Research Institute. Plastics Study Group,
1955
4
Encapsulation Technologies for Electronic Applications - Sayfa 290
Durometer hardness test can indicate the curing quality of the plastic encapsulant material based on hardness. The term durometer was originally used by A.F. Shore in 1920s referring to his measurement device, but now it is used for both the ...
Haleh Ardebili, Michael Pecht,
2009
5
Characterization and Failure Analysis of Plastics - Sayfa 194
Rockwell testing and the durometer test method are the most common, although another type of hardness test for plastics is the Barcol method. A rough ... The hardness value is often used as a measure of the degree of cure of a plastic.
ASM International, Steve Lampman,
2003
6
Handbook of plastic compounds, elastomers, and resins: an ...
350 psi; tens. elong. 500%; Shore hardness A 0-8. SWS-7810u. [Wacker Silicones] Silicone rubber compd. (methyl vinyl polysiloxane); extremely low durometer compd. for low deflection mold rolls; very low modulus, good surface release, and ...
Michael Ash, Irene Ash,
1992
7
Search of Excellence, ANTEC 91 - Sayfa 2405
Society of Plastic Engineers ... Butylene-Styrene, silicone fluid TPE blend^ results in good compatibility, excellent processability , excellent acid resistance, low durometer, good tensile and elongation, and a very smooth surface. The above ...
Society of Plastic Engineers,
1991
8
Handbook of Plastics Testing and Failure Analysis - Sayfa 86
For softer materials such as flexible PVC, thermoplastic rubbers, and polyethylene, Durometer hardness is measured. The typical hardness values of some common plastic materials are listed for comparison in Table 2-3. A comparison of ...
9
Plastics Design Handbook - Sayfa 315
Durometer hardness An arbitrary numerical value that measures the resistance to intention of a blunt indenter point of the ... It is a measure of the hardness of a plastic, that includes laminate or reinforced plastic, using a Barber Coleman spring ...
D.V. Rosato, Marlene G. Rosato,
2013
10
Plastic product design - Sayfa 407
The Shore "A" instrument employs a sharp indenter point with a load of 56 to 822 grs. This is the type of durometer used for rubber and some plastic materials. The Shore "D" instrument is used for very hard plastics. It has a blunt point, and a ...