«HEX KEY WRENCH» தொடர்புடைய ஆங்கிலம் புத்தகங்கள்
பின்வரும் புத்தக விவரத்தொகுப்புத் தேர்ந்தெடுப்பில்
hex key wrench இன் பயன்பாட்டைக் கண்டறியுங்கள்.
hex key wrench தொடர்பான புத்தகங்கள் மற்றும் ஆங்கிலம் இலக்கியத்தில் அதன் பயன்பாட்டுச் சூழலை வழங்குவதற்கு அதிலிருந்து பெறப்பட்ட சுருக்கமான சாரங்களைத் தொடர்புபடுத்துகின்றன.
1
Use and care of hand tools and measuring tools
HEX KEY WRENCH (SHORTER SECTION) The hex key wrench is an L-shaped,
six-sided wrench. Both ends of the "L" are the same size so you can turn the
wrench either to gain access to the screw head or to obtain a leverage advantage
.
United States. Dept. of the Army, 1983
2
Precision Machining Technology
Examples of these wrenches are shown in Figure 3.3.13. Hex Key wrench Hex
key wrenches are used on socket head cap and set screws. They are frequently
used on cutting toolholders FIgUre 3.3.11 Socket wrenches are available in 6-
point ...
Peter Hoffman, Eric Hopewell, Brian Janes, 2014
3
Direct and general support maintenance manual: boat, bridge ...
Using 5/16 in hex key wrench, remove 3/8 in pipe plug line pressure tap located
above regulator valve. 2. Connect hydraulic pressure gage to line pressure tap.
NOTE Transmission must be in neutral for first test. 3. Start engine. 4. Follow chart
...
United States. Dept. of the Army, 1990
T-handle wrench speeds hex-key work You can save time when using hollow-
head safety screws by cutting off the short leg of a hex-key wrench and chucking
the longer leg in a T-handle tap wrench (as illustrated above). One T handle will ...
... of VM in. deep and and weighs less than 4 11:V1(; in. wide. pounds and has
cutting ca- The abrasive plane is de- To change the abrasive sleeve, first insert a
locking pin to secure the arbor. Then remove the screw with a hex-key wrench.
6
Bill Hylton's Ultimate Guide to the Router Table
It enables you to change bits in seconds with a hex-key wrench. No need to hold
a spindle lock or fumble with an open- end wrench. Hold the bit in one hand and
twist the hex key to tighten the collet with the other. Controlling the Bit Opening ...
Thread the hex- socket screws into the adjustable pivots with a hex-key wrench (
photo 14). Cut the U-shaped plastic door tracks to length and press them into the
grooves routed in the cabinet sides. If the tracks fit loosely, apply a few spots of ...
8
Organizational Maintenance Manual: Concrete-mobile Mixer ...
Hold setscrew (11) with hex key wrench while turning nut. Do not tighten. Pin
wheel towards spring. Calibration numbers toward the front. 19. Retainer stem (2)
. Tighten carefully until meter cannot be rotated with fingers. Use hex key wrench.
9
Operator's Manual: Automated Data Processing System ...
o. o. lO. Using 5/32-inch hex key wrench, loosen bolt enough to move bracket. ll.
Using 5/32-inch hex key wrench, remove bolt. l2. Tag bolt as shown. l3. Slide
bracket into position shown. l4. Replace tagged bolt and tighten. l5. Lower cover.
(i) Strap wrench (ii) Torque wrench (iii) Hex key wrench What is a torque wrench?
It is used when it is necessary to know the amount of turning or twisting applied to
a nut. Name the material out of which a vice is made. Body: Cast iron Fixed ...
«HEX KEY WRENCH» வார்த்தையைக் கொண்டுள்ள புதிய உருப்படிகள்
பின்வரும் செய்தி உருப்படிகளின் சூழலில்
hex key wrench என்ற வார்த்தையைப் பயன்படுத்துவது பற்றியும் எப்படிப் பயன்படுத்துவது என்பதைப் பற்றியும் தேசிய மற்றும் பன்னாட்டு அச்சகங்கள் என்ன பேசியிருக்கின்றன என்பதைக் கண்டறியுங்கள்.
Trim your trees without needing a ladder to reach the high branches
The Sun Joe Electric Multi-Angle Telescopic Pole Chain Saw comes with safety glasses and a hex key wrench/blade screwdriver. It's QVC's ... «The Gadgeteer, மார்ச் 15»
Ratcheting Hex Key Wrench Makes Furniture Assembly A Snap
Most furniture usually comes with a tiny hex wrench (more usually an allen key around these parts) as to help you put it together, but they aren't ... «Lifehacker Australia, மே 11»
இல் உள்ள வார்த்தைகளில் மறைக்கப்பட்டிருக்கும் எல்லாவற்றையும் கண்டறியுங்கள் 
