İngilizce sözlükte "castle nut" sözcüğünün anlamı

İNGILIZCE DİLİNDE CASTLE NUT SÖZCÜĞÜNÜN OKUNUŞU

castle nut

CASTLE NUT SÖZCÜĞÜ İNGILIZCE DİLİNDE NE ANLAMA GELİR?

Kastellenmiş somun

Castellated nut

Kale bağlantısı veya yivli somun olarak da bilinen kale şeklinde bir somun, bir uca kesilmiş delikli bir somundur. Adı, fıstık ile ortaçağ kalesinin mırıltılı parapetine benzemektedir. Cıvata veya dingil dişli ucu üzerinden delinmiş bir veya iki delik içerir. Somun doğru döndürülerek sıkılır ve sonra yuva bağlantı elemanındaki delikle hizalanmazsa, somun en yakın yuvaya doğru döndürülür. Somun daha sonra bölünmüş bir iğne veya emniyet teli ile sabitlenir. Olumlu bir kilitleme cihazıdır. Kastellenmiş fındık, bir tekerlek yatağı tutma gibi düşük torklu uygulamalarda kullanılır.

A castellated nut, also called a castle nut or slotted nut, is a nut with slots cut into one end. The name comes from the nut’s resemblance to the crenellated parapet of a medieval castle. The bolt or axle has one or two holes drilled through its threaded end. The nut is torqued properly and then, if the slot is not aligned with the hole in the fastener, the nut is rotated forward to the nearest slot. The nut is then secured with a split pin or safety wire. It is a positive locking device. Castellated nuts are used in low-torque applications, such as holding a wheel bearing in place.

İngilizce sözlükte castle nut sözcüğünün tanımı

Sözlükte kale somununun tanımı kafasında altı yuvalı olan altıgen bir somun olup ikisi, ikisi de sıkıca yerine oturması için bir kilitleme pimi almaktadır.

CASTLE NUT SÖZCÜĞÜNÜN ÇEVİRİSİ

Çok dilli İngilizce çevirmenimiz ile castle nut sözcüğünün 25 dile çevirisini bulun.

Bu bölümde verilen castle nut sözcüğünün İngilizce dilinden diğer dillere çevirisi otomatik istatistiksel çeviri ile elde edilmiştir ve temel alınan çeviri birimi İngilizce dilindeki «castle nut» sözcüğüdür.

• İngilizce - Çince Çevirmen: 城堡螺帽
• İngilizce - İspanyolca Çevirmen: tuerca castillo
• İngilizce: castle nut
• İngilizce - Hintçe Çevirmen: महल अखरोट
• İngilizce - Arapça Çevirmen: قلعة الجوز
• İngilizce - Rusça Çevirmen: замок гайка
• İngilizce - Portekizce Çevirmen: castelo porca
• İngilizce - Bengalce Çevirmen: দুর্গ বাদাম
• İngilizce - Fransızca Çevirmen: château écrou
• İngilizce - Malezya Dili Çevirmen: Kacang istana
• İngilizce - Almanca Çevirmen: Kronenmutter
• İngilizce - Japonca Çevirmen: 城ナット
• İngilizce - Korece Çevirmen: 성 너트
• İngilizce - Cava Dili Çevirmen: Kastil kacang
• İngilizce - Vietnamca Çevirmen: hạt lâu đài
• İngilizce - Tamil Çevirmen: கோட்டை நட்
• İngilizce - Marathi Çevirmen: किल्ला
• İngilizce - Türkçe Çevirmen: çentikli somun
• İngilizce - İtalyanca Çevirmen: dado a corona
• İngilizce - Lehçe Çevirmen: nakrętka zamek
• İngilizce - Ukraynaca Çevirmen: замок гайка
• İngilizce - Romence Çevirmen: piuliță castel
• İngilizce - Yunanca Çevirmen: παξιμάδι κάστρο
• İngilizce - Afrika Dili Çevirmen: kroonmooer
• İngilizce - İsveççe Çevirmen: kronmuttern
• İngilizce - Norveççe Çevirmen: slott mutter

«CASTLE NUT» İLE İLİŞKİLİ İNGILIZCE KİTAPLAR

castle nut sözcüğünün kullanımını aşağıdaki kaynakça seçkisinde keşfedin. castle nut ile ilişkili kitaplar ve İngilizce edebiyattaki kullanımı ile ilgili bağlam sağlaması için küçük metinler.

Machine Drawing

5.10.3 Locking by Castle Nut A castle nut is a hexagonal nut with a cylindrical collar turned on one end. Threads are cut in the nut portion only and six rectangular slots are cut through the collar. A split pin is inserted through a hole in the bolt ...

K. L. Narayana, 2007

Design of Machine Elements

Another common method to obtain positive locking of threads is to use a castle nut with a split pin. It is shown in Fig. 7.6. The castle nut consists of the usual hexagonal nut but with an addition of upper cylindrical part. This cylindrical portion ...

V. B. Bhandari, 2010

Introduction to Machine Design

6.5 Jam Nut One common method to obtain positive locking of threads is to use castle nut with a split pin. It is shown in Fig. 6.6. The castle nut consists of usual hexagonal nut but with an addition of upper cylindrical part. This cylindrical portion ...

V B Bhandari, 2001

Direct Support, General Support, and Depot Maintenance ...

Never back up nut to align hole in shaft with hole in castle nut; always turn nut to the next opening. (7) Reassemble the remaining finger gear in the same manner as discussed in steps 2 through 6 above. (8) Reassemble the outer gear case ...

The MG Midget and Austin Healey Sprite High Performance Manual

So here you can see the king pin has been drilled for a split pin, and uses an aviation AN castle nut. Brake pads (from left): MGB V8, MGB, Midget/Sprite. Peter May Engineering 9in disc kit fitted to a wire wheel Sprite. Note the green marks are ...

Daniel Stapleton, 2008

Practical Fabrication and Assembly Techniques

Standard-height and thin (half-height) castle nuts are shown in the accompanying illustration (Figure 7). Another style of nut you'll come across is a castle nut. In aircraft applications, castle nuts are most often used for tension loads.

Wayne Scraba

Organizational Maintenance: Truck Tractor, Line Haul, 50,000 ...

Install castle nut (14) 2. 1. Steering arm (11) Castle nut (14) and steering arm (11) . CAUTION Place nut on threaded end of steering arm (11), and finger tighten. If dust boot (12) was removed during disassembly, install dust boot onto drag link ...

How to Build Cobra Kit Cars

Install Cotter PininCastle Nut 3 With everything aligned properly, hammer and spread open the cotter pin, thus locking the castle nut into a secure and safe position. A flashlight helps to find the hole for the cotter pin. 2 After using the supplied ...

D. Brian Smith, 2012

MotorBoating

(3) Two 16 inch Stillson wrenches or one Stillson, plus one properly sized heavy box or open-end wrench for the castle nut. (4) One mallet, heavy hammer or metal piece to seat, wheel. (5) One large, adjustable box pliers. ' (6) One box wrench ...

‎

How to Rebuild Corvette Rolling Chassis 1963-1982

Push the power steering cylinder ball joint stud into the steering relay rod from the rear, and install the castle nut. Torque the castle nut to 45 ft-lbs. Insert a stainless-steel cotter pin in the castle nut, and bend the ends of the cotter pin around the ...

George McNicholl

«CASTLE NUT» TERİMİNİ İÇEREN HABERLER

Ulusal ve uluslararası basında konuşulanları ve castle nut teriminin aşağıdaki haberlerde hangi bağlamda kullanıldığını keşfedin.

CURT's Most Advanced Weight Distribution Hitch Yet

The cam system also has a hex castle nut for easy adjustment to fit most industry-standard couplers. Finally, setup of the CURT TruTrack™ is ... «PR Web, Nis 15»

ATI debuts its new translucent Omni hybrid receiver set

Polymer threads can be ruined by cross-threading or over-torquing the castle nut while being assembled. This is especially true for stripped ... «Guns.com, Nis 15»

Magpul update: M-Lok, MOE+ and bench blocks galore (VIDEO)

The castle nut teeth are extended to work specifically with Magpul's ASAP sling plate. It has cutouts for flash hiders and other muzzle devices ... «Guns.com, Kas 14»

What You Need to Convert a VEPR—StormWerkz and Bonesteel …

Keep in mind you 'll need a tube, castle nut and endplate. *************************. profile 1. Bonesteel's folder is "plug and play". Just pop it in ... «Hawaii Reporter, Ağu 14»

Troy Industries AK Battlerails now available

It uses an adjustable tensioner that locks in place with a castle nut. This not only holds it in place it means that the rail can be installed on a ... «Guns.com, Tem 14»

FIRST LOOK! 2015 KAWASAKI KX450F

Gone is the castle nut on the rear axle and in its place is self-locking rear axle nut. The design holds 80 foot-pounds of torque (without the need ... «Motocross Action Magazine, Tem 14»

Gun Test: Stag 3T M

... six-position adjustable stock—and a sling-attachment plate, with left- and right-side cut-outs for sling clips, secured just under the castle nut. «Daily Caller, Haz 14»

ARMagLock AR-15 Fixed Magazine Lock Installation Photo Guide

The easiest way to remove your takedown pin without undoing the castle nut and stripping the staking is to do the following. Pull the rear ... «AmmoLand.com, Nis 14»

On Target Review: Arsenal SM-13 Optics Mount

The castle nut adjustment for the QD lever was the secret sauce. It allows you to use the mount on a variety of AKs of different dimensions by ... «Hawaii Reporter, Mar 14»

2013 in Review: Holiday gift list for police officers

It even has a castle nut wrench and a sight adjustment tool. If you carry a carbine, you should carry this tool. It's a little bigger and comes with a larger package of ... «Police News, Ara 13»