GRUB SCREW SÖZCÜĞÜ İNGILIZCE DİLİNDE NE ANLAMA GELİR?
Ayar vidası
Ayarlanmış vida, bir cisimi başka bir cisim içine veya diğer cisme karşı korumak için genellikle kullanılan bir vida türüdür. En yaygın örnekler bir kasnak veya dişliyi bir mile sabitlemektir. Ayar vidaları genellikle başsızdır, yani vidanın tamamen dişli olduğu ve vida dişinin büyük çapının ötesine çıkıntı yapan başı olmadığı anlamına gelir. Kör vidalı mil, neredeyse her zaman, altıgen yuva, yıldız, kare yuva veya yuva gibi bir iç açıcı tahrik ile tahrik edilir. Ayarlanan vida, dış nesnedeki dişli bir delikten geçer ve dıştaki nesneye göre hareket etmesini önlemek için iç nesneye karşı sıkılır. Delikten çıkıntı yapan alt uç boyunca sıkıştırma veya sıkıştırma kuvveti uygular. Yerleştirmek için ayar vidasına sahip bir potansiyometre düğmesi. Örnek bir uygulama, bir ayar vidası bir kasnak göbeğine vidalandığı zaman, uç noktası milin üzerine sıkıca dayanmasıdır. Tespit işlemi, bir veya her ikisinin bir miktar elastik veya plastik deformasyonuyla genellikle vida ile şaft arasındaki sürtünmeye dayanmaktadır.
İngilizce sözlükte grub screw sözcüğünün tanımı
Sözlükte grub vidasının tanımı, bir tornavida için bir yarık kesimi veya bir altıgen anahtar için bir yuvaya sahip küçük bir başsız vidadır ve belirlenen bir konumda bir kayan bileşeni sabitlemek için kullanılır.
«GRUB SCREW» İLE İLİŞKİLİ İNGILIZCE KİTAPLAR
grub screw sözcüğünün kullanımını aşağıdaki kaynakça seçkisinde keşfedin.
grub screw ile ilişkili kitaplar ve İngilizce edebiyattaki kullanımı ile ilgili bağlam sağlaması için küçük metinler.
a) pulley fixed with key in keyway b) cotter pin assembly c) splined shaft grub-
screw d) grub-screw Figure 4.4.3 Shaft fixings more economical to cut the keyway
over the entire length of the shaft. Any amount of additional pulleys can be added
...
Lesley Cresswell, Barry Lambert,
2003
2
Ford Cleveland 335-Series V8 Engine 1970 to 1982
To prevent the grub screw falling off the Allen key, the block is simply turned
upside down, so that the grub screw can be started in the second part of the
drilled and tapped hole in the block; when the thread bottoms out, it is firmly
tightened.
3
Essential Bicycle Maintenance & Repair
... easier to fine-tune but are not quite as simple to work with . They use a similar
clamping structure as a single-clamp bolt seatpost, but the bottom half of the
clamp can be fine-tuned with a separate grub screw that tilts the base up and
down .
4
Organizational Maintenance Manual: Topographic Support ...
(6) Remove compression spring (16) from grub screw (17) (7) Loosen two nuts (
18) and remove grub screw (17) from cam lever (15). (8) Remove spring tension
pin (19) and remove pin (20), bearing (21), and roller (22) from cam lever (15).
5
German Technical Dictionary
... thread lead angle Gewindestift m 1. <Bau> grub screw; 2. <Fertig> grub screw (
Kunststoffinstallationen); 3. <Maschinen> grub screw, headless pin; 4. <Mechan>
headless screw Gewindestopfen m <Bau> screw plug Gewindestrehlen n 1.
6
Micromanipulation in Assisted Conception
Locate the grub screw in the end of the control knob. Grip the control in one hand
and loosen the grub screw with an appropriate-sized Allen key. Once the grub
screw is loosened, the control knob can be unscrewed from its thread. Screw the
...
Steven D. Fleming, Robert S. King,
2003
7
Your First Atlantic Crossing 4th Edition: A Planning Guide ...
A grub screw near the top of the forestay had unwound a thousandth of an inch or
two and the swivel could not slide past. We rigged the bosun's chair and hauled
Julia to the masthead. She lassoed the forestay and tied a bight of line around ...
8
How to Modify Volkswagen Bus Suspension, Brakes & Chassis ...
(Courtesy Alex Leighton) Clean up 6in each side of the grub screw hole all
around the beam using a grinder, and mark the beam. (Courtesy Alex Leighton)
Fitting a Foksy front beam adjuster The top beam (the one without the steering ...
Assembly of the neck onto the stem on the dovetail rail locked with a grub screw
The connection of the components has been designed taking into account that
the shoulder is a very mobile joint: • The head is fixed to the neck on a Morse
taper ...
Gilles Walch, Pascal Boileau,
1999
10
FCS Concrete Structures L2
Instead of using an ordinary nut to tighten the tie, you use what is called a ferrule
rose with a grub screw, and you tighten the screw with a special ferrule tightener
jack. A ferrule rose gets its name from its shape. A grub screw is a screw that ...
Steve Crosswell, Penny Swift,
2007
«GRUB SCREW» TERİMİNİ İÇEREN HABERLER
Ulusal ve uluslararası basında konuşulanları ve
grub screw teriminin aşağıdaki haberlerde hangi bağlamda kullanıldığını keşfedin.
'Maker' Dad 3D Prints His Own Miniature Table Saw & It Works …
... 100% 3D printed, is built with the aforementioned saw blade, as well as M3 and M6 bolts, bearings, nuts, a 110V DC motor, and a grub screw ... «3DPrint.com, Haz 15»
That time I built the Mad Max Interceptor
mad-max-interceptor-iphone-03. The grub screw holding the blower pulley wheel in place failed and the pulley spun off the spline – at speed. «CarAdvice, May 15»
Azonic Bigfoot MTB pedals
The platform isn't concave and Azonic has tried to compensate for this by using extra long grub screw pins on the outside edges of the pedal ... «BikeRadar.com, May 15»
Serpent Announces New Cobra E 2.1 1/8 4WD Buggy
The lower shock-mounting pins are secured with a small grub screw from the bottom. Front anti-roll bar. The ball raced front anti-roll bar system, ... «Radio control Car Action, Nis 15»
Volvo Ocean Race Leg 3 - Dongfeng Race Team pushing hard!
There is a pin to hold the strop to the top of the ram then a 3mm grub screw to secure the pin in place, trying to get this in was not an easy task ... «Sail World, Oca 15»
Pilot notes
Letting a 9 lb 4oz (4.2kg) model rely on the integrity of a single, small, grub screw isn't my cuppa. It's far better to let one elevator pushrod continue to a swing ... «ModelFlying, Oca 15»
A Lightsaber Katana Is The Closest We'll Get To Star Wars In Real Life
There don't seem to be any pegs and if it's just a grub screw, that's an accident waiting to happen. Other than that it's not the proper Japanese ... «Gizmodo Australia, Ağu 14»
KS Lev Seatpost Review | Hammered
A grub screw clamps the cable to a cam but over this a neat 'o' ringed and push fit red anodised cover is all that holds this set up in place – a ... «Dirt Mountainbike, Ağu 14»
Trek 2015 road range - an overview
(Matthew Allen/Bikeradar). We're pleased to see that Trek has retained the Domane's hidden mudguard mounts - that's the grub screw above ... «BikeRadar.com, Tem 14»
Camera, Fish, Action!
Version one was a short length of timber dowel mated to the motor shaft via drilled hole and grub screw. A GoPro tripod mount was Araldited to ... «Fishing World, May 14»