ЩО CROSSHEAD ОЗНАЧАЄ У АНГЛІЙСЬКА?
Хрестовик
Крестовик - це механізм, використовуваний у великих верстатах зі зворотним зв'язком і поршневі компресори для усунення бічного тиску на поршень.
Визначення crosshead у англійська словнику
Перше визначення кросхед в словнику - заголовок підрозділу або заголовка, надрукований в тексті тексту. Інше визначення кроссоведа - це блок або промінь, зазвичай утримувані підшипниками ковзання в механізмі зворотного потягу, а саме приєднання між поршневим стержнем і шатункою двигуна. Crosshead також є стійкою, встановленою через верхню частину рулевого посту, до якого прикріплений кузовний пристрій.
10 АНГЛІЙСЬКА КНИЖКИ ПОВ'ЯЗАНІ ІЗ «CROSSHEAD»
Дізнайтеся про вживання
crosshead з наступної бібліографічної підбірки. Книжки пов'язані зі словом
crosshead та короткі уривки з них для забезпечення контексту його використання в англійська літературі.
is compared with a feedback signal from a transducer monitoring the position of
the crosshead. Using this feedback circuit, the desired boundary condition can be
achieved. Tensile tests usually can be carried out at a constant crosshead ...
18.2.2 Steam Engine Crosshead Crosshead is used in horizontal steam engines
for connecting the piston rod and connecting rod. Figure 18.2 shows the part
drawings of a steam engine crosshead. The crosshead, with the help of slide
block ...
3
A History of the American Locomotive: Its Development, 1830-1880
The crosshead pump was the most common type used on American locomotives.
It was the simplest and cheapest arrangement possible. The pump plunger was
connected to the crosshead and worked in line with the locomotive's piston rod; ...
22.2.6 Crosshead and Piston Rod for a Vertical Steam Engine The length of the
piston rod in small steam engines is relatively small, in which case the piston rod
can be connected directly to the connecting rod. In engines of the high-power ...
5
Locomotive Cyclopedia of American Practice
section, the arms of which slide between pairs of upper and lower guides. The
body suspended from and sliding on and between the lower guide bars. With this
type of crosshead a single upper guide bar is sometimes used. Laird Type Cross
...
Crosshead Arm (Walschaert \'alve Gear). 263, Figs. 101140; 14, Figs. 841-847;
Figs. 850, 851. A short bar rigidly attached to the crosshead in a vertical position,
and holding one end of the UNION' LlNK, which see, that serves to transmit its ...
7
Locomotive dictionary: an illustrated vocabulary of terms ...
The brass of a main rod or side rod is fitted to it, and its function is to transmit the
reciprocating motion imparted to the piston, piston rod, crosshead and main rod
by the expansive force of the steam, to the rotating driving wheel. Crank pins are
...
American Railway Master Mechanics' Association,
1906
8
Official Gazette of the United States Patent Office
In a cork puller, a plurality of parallel guides, an upper cross head slidabiy fitted
to said guides, a lower crosshead slidabiy fitted to said guides independently the
upper crosshead, a nut on the lower crosshead, an extractor screw connected to
...
United States. Patent Office,
1913
9
A Practical Guide to Compressor Technology
(a) (b) FIGURE 2.54 Flanged crosshead: (a) plan view; (b) front view. 2.14.3
Crosshead Designs and Attention to Reliable Lubrication Modern machines with
piston rods 4 in. or more in diameter often use a flanged crosshead design (see
Fig.
10
3. Forsthoffer's Rotating Equipment Handbooks: Compressors
The connecting rod can be bumped back and forth at the crosshead and
movement recorded between the crankshaft and the connecting rod. Acceptable
readings should be obtained from the compressor vendor. Figure 26.17 Crankpin
...
William E. Forsthoffer,
2005
НОВИНИ ІЗ ТЕРМІНОМ «CROSSHEAD»
Дізнайтеся, що обговорювала національна та міжнародна преса, і як термін
crosshead вживається в контексті наступних новин.
Full text access provided to Google
Ltd., Kanagawa, Japan) with a crosshead speed of 10 mm min−1. The tensile modulus was determined by the initial slope of the stress–strain ... «Nature.com, Липень 15»
Know it all
The easy-to-use crosshead Phillips screwdriver quickly became essential on automobile assembly lines. ***. A person's foot has an average of ... «San Mateo Daily Journal, Червень 15»
Victory at the Gaelic Grounds would lay down a significant marker …
Crosshead. This can sound a bit like whistles echoing off tombstones given the number of players – Barrett, Corbett, McGrath, Cahill – that the ... «Irish Times, Червень 15»
Nanoporous-gold-based composites: toward tensile ductility
A feedback loop controlled and progressively reduced the crosshead speed so as to maintain a constant true strain rate at 10−4 s−1 while the ... «Nature.com, Червень 15»
The use of hydraulic nuts for compressor crosshead applications
The nuts are used at the crosshead joint and it is here that the piston rod is locked to the crosshead to prevent rotation. A technical manager at ... «Energy Global, Червень 15»
Mabey Hire Wins ICE Wales Innovation Award
The initial solution proposed by Dawnus Construction was to remove the existing reinforced concrete crosshead and piers by saw cutting them ... «RealWire, Травень 15»
NSR2: 2015 US Team Candidates Named in M1x, W1x, M4x, LM2x
... for getting race experience here, with a time trial in a raging and choppy tail, and much better conditions this morning in a light crosshead. «row2k.com, Травень 15»
More former hospital land sold off
Crosshead The development, which will be partially funded by a £720,000 grant from the Homes and Communities Agency's Affordable Homes ... «Daily Echo, Травень 15»
Guill offers dies for six-layer coextrusion
Inc. featured its line of crosshead and inline tubing dies at NPE 2015. The company introduced the Series 800 extrusion tooling for two to six ... «Plastics News, Травень 15»
See a Korg MS-20m kit being built in 37 seconds
When we reviewed Korg's MS-20m kit, we noted that in order to build it you'd require "a crosshead screwdriver, about three hours and some ... «MusicRadar.com, Квітень 15»