10 АНГЛІЙСЬКА КНИЖКИ ПОВ'ЯЗАНІ ІЗ «DRIFTPIN»
Дізнайтеся про вживання
driftpin з наступної бібліографічної підбірки. Книжки пов'язані зі словом
driftpin та короткі уривки з них для забезпечення контексту його використання в англійська літературі.
1
Routledge Diccionario Técnico Inglés
... conductor de corriente m prod current- conducting pin; - conico m ing meca
drift pin, driftpin, drift punch, taper doweL taper pin, meca taper pin; - conico
cuadrado m ing meca square driftpin; - conico de ensanchar m ing meca cutting
driftpin; ...
2
Organizational maintenance manual: tractor, wheeled (DED) ...
Stabilizer (5) and cylinder rod end (9) Cylinder rod end end pin (6) Using 3-
pound head cross-peen hammer and 3/4-inch brass-tipped driftpin, drive out.
STABILIZERS - CONTINUED LOCATION ITEM ACTION REMARKS WARNING
Some ...
3
Crane-shovel: Power Unit, Revolving Truck Mounted, Pneumatic ...
(4) When the end of the drag cable is reached at the front drum (15), pry the
wedge loose by inserting a driftpin from the outside of the drum. (5) Continue
pulling and coiling or reeling the drag cable from the boom pulley. After coiling,
wrap ...
4
Direct Support and General Support Maintenance: Truck, ...
Using ball-peen hammer and 1/2-inch brass driftpin, tap out. Using arbor press,
take off. Using 1/2-inch driftpin and ball-peen hammer, tap out. LOCATION ITEM
ACTION REMARKS ASSEMBLY 13. Injection pump drive shaft 2-326 TM ...
5
The Southwestern Reporter
T. A. Gillespie Co., 69 N. J. Law, 279, 55 Atl. 276 (driftpin); Demato v. Hudson
County Gas Co., 74 N. J. Law, 793, 67 Atl. 28 (chisel); Martin v. Highland Park
Mfg. Co., 128 N. C. 264, 38 S. E. 876, 83 Am. St. Rep. 671 (hammer); Meyer v.
6
Russian Engineering Research
In the design of the vibration driftpin shown in Fig. a, use is made of the
combination of electromagnets that cause the successive elongation of sections
beginning from the first one in the direction of the driftpin movement in the hole.
7
Operator's, organizational, direct support, and general ...
NOTE Bearing cups should be removed only if replacement is necessary.
Bearing cups should always be replaced if bearing cones are being replaced. 6.
Hub(1) Two bearing cups (11) Using 1-pound ball-peen hammer and brass
driftpin, tap ...
8
Operator's Manual: Armored Reconnaissance/airborne Assault ...
(3) Drive out track pin centered in clamp assembly; then withdraw driftpin (1). (4)
Tap shoes with hammer or pry with crowbar to separate shoes. If necessary,
loosen clamp assembly to disengage (5) Drive out second track pin and remove
...
9
Operator, Organizational, Field and Depot Maintenance ...
Using a driftpin, drive out the two pins (15) that secure the flyweights to the
flyweight hub (18). e. Support the governor housing (4) on its face, and, entering
the housing through the pipe fitting hole in the rear, use a driftpin to drive out the
pin ...
10
Routledge Dictionnaire Technique Anglais
427 manoonique driftpin; - à comhinaisons m cons meca comhinatlon chuck; -
conformateur de tuhes de chaudière m lnst hyoa hoiler pipe shaping mandrel; -
de coulès m peouuction gate pin, gate stick, runner stick, ruoner pin; - à
coussinats ...
