ЩО ÇELIK METRE ОЗНАЧАЄ У ТУРЕЦЬКА?
Визначення çelik metre у турецька словнику
стальний метр Вимірювальний інструмент виконаний з тонкого сталевого металу, який можна вставити у маленьку коробку, позначену вимірювальними агрегатами.
10 ТУРЕЦЬКА КНИЖКИ ПОВ'ЯЗАНІ ІЗ «ÇELIK METRE»
Дізнайтеся про вживання
çelik metre з наступної бібліографічної підбірки. Книжки пов'язані зі словом
çelik metre та короткі уривки з них для забезпечення контексту його використання в турецька літературі.
1
Design of Steel Structures - Sayfa 7
The designations of various types of rolled steel sections are listed in Appendix I. An I-section is designated by its depth and weight, e.g., I.S.L.B. ... 750 N/m means, the I-section is 500 mm deep and the self weight is 750 N per metre length.
2
Structural Steel Design to BS 5950 - 1. bölüm - Sayfa 86
Steel beams having a clear span of 9.35 m are resting on 150 mm wide end bearings. The beams are spaced 3 m apart and carry a dead load of 5 kN/m:, including an allowance for the weight of the section, and an imposed load of 15 kN/m2 ...
Frixos Joannides, Alan Weller,
2002
3
LIMIT STATE DESIGN IN STRUCTURAL STEEL - Sayfa 374
Load per metre span of purlin. Here (a) Sheeting 46 N/m2 X 1.65 m I 76 N/m (b) Self-weight of purlin I 36 N/m (refer to Table 14.2 of this chapter) Dead load I 76 + 36 I 112 N/m Using fastening material 8 N/m: Total dead load I 120 N/m I 0.12 ...
4
Connections in Steel Structures III: Behaviour, Strength ... - Sayfa 532
An overall cost saving for the fabricated plane frame delivered and erected within a 100 miles radius of the shops averaged about 5.5% against “simple” construction. 2 bay frame 2 bay frame "7 storeys s in * B in 4 storeys # : |- - # . - - m fi ...
R. Bjorhovde, A. Colson, R. Zandonini,
1996
5
Design Of Steel Structures (By Limit State Method As Per ... - Sayfa 5
(vii) Rolled steel Plates (viii) Rolled steel Flats (ix) Rolled steel Sheets and Strips. ISI Hand Book for Structural Engineers-I gives nominal dimensions, weight per metre length and geometric properties of various rolled steel sections.
6
Steel Carriage by Sea - Sayfa 33
A round steel billet is removed from the furnace and the end is pierced in a rotary piercing mill. ... Popular sizes range from 8mm outside diameter, wall thickness 1mm, weight 0.173 kg per running metre to 105 mm outside diameter, wall ...
7
Ship Design and Performance for Masters and Mates - Sayfa 19
Worked example 2.1 A basic ship is 121.95m 16.46m 9.15m Depth Mld with a total steel weight of Ws. A new similar design is 131.1m 17.07m 10.06m Depth Mld. Show the method for obtaining the steel weight for the 131.1 m ship. L B D Basic ...
8
Iron and Steel in Ancient China - Sayfa 195
A rather sudden development, perhaps in the mid-third century B.C., is the bronze "long sword", typically about a metre long. An example, from the First Emperor's mausoleum, is shown in figure 4.41 . Most iron swords are also long (see table ...
9
Steel Designers' Manual - Sayfa 1176
Steel Construction Institute (Great Britain) Buick Davison, Graham W. Owens. 1.2 Dimensional ... 2 Dimensions of section 2.1 Masses The masses per metre have been calculated assuming that the density of steel is 7850 kg/m3. In all cases ...
Buick Davison, Graham W. Owens, Steel Construction Institute (Great Britain),
2012
10
Prestressed Concrete Bridges - Sayfa 57
20 = /„ = 16 The quantity of reinforcing steel is obtained by multiplying the total volume of concrete by the mass of steel per ... The parameter ms is estimated using the equation where lm is in metres and ms is in kilograms per cubic metre of ...
Christian Menn, Paul Gauvreau,
1990