与 «MILLIHENRY»相关的英语书籍
在以下的参考文献中发现
millihenry的用法。与
millihenry相关的书籍以及同一来源的简短摘要提供其在 英语文献中的使用情境。
The approximate value of the coefficient of self-induction of the coil will be (
MPPET 1996) (a) 25 millihenry (b) 25 x 10- 3 millihenry (c) 50 x 10-3 millihenry (d
) 50 x 10-3 henry 96. An e.m.f. of 100 millivolts is induced in a coil when the
current in ...
The aerial itself will then be of 0.0012 microfarad capacity and 0.023 millihenry
inductance, and the loading-coil will have 0.35 millihenry inductance. This last
named figure is the sum of the inductances of secondary and loading-coil in ...
3
Bureau of Standards journal of research
Entering with L as abscissa, the value of l/i* is obtained and d' is multiplied by it to
get the first preliminary (L millihenry) value D' of wire diameter. Like d' in the 1-
millihenry case, this value applies for wire of zero-thickness insulation, and, like ...
United States. National Bureau of Standards, 1932
4
Comprehensive Objective Physics
The coefficient of mutual induction between the two coils will be (a) 1 millihenry (
6) 10 millihenry (c) 100 millihenry (d) 1000 millihenry. [MP PET 1996] X and Y are
solenoids wound on cardboard tubes. X carries a constant current I as shown ...
Narinder Kumar, Dr. J. K. Juneja, 2006
5
Introduction to Electronics
The henry is a large unit; the millihenry (mH) and microhenry (H) are more
commonly used. 10–1. QUESTIONS 1. Define inductance. 2. What is the unit for
measuring inductance? 3. Define a henry. 4. What letter is used to represent ...
6
Practical Problems in Mathematics for Electronic Technicians
A 25-millihenry coil is in a circuit operating at 40 kilohertz. Compute the inductive
reactance of the coil. 3. What frequency is being applied to the 120-millihenry coil
in this diagram? O 1 3,768 4. A coil has a 7.5-kilohm reactance to a 2,000-hertz ...
7
Introduction to Basic Electricity and Electronics Technology
I EXAMPLE: How much current flows through a 250-millihenry inductor when a
signal of 12 volts and 60 hertz is applied across it? Given Solution XL I ? First,
find the inductive reactance (XL). 71' I 3.14 XL I 2arfL fI 60Hz xL I (2)(3.14)(60)(
0.25) ...
8
PCB Design Using AutoCAD
Inductors are usually in the .1 microhenry to 10 henry range, with millihenry
values quite common. By convention, MH stands for millihenry. Table 2-3
Engineering Units UNIT CONVENTIONAL SYMBOL Capacitance picofarad PF
nanofarad NF ...
9
Genetic Programming IV: Routine Human-Competitive Machine ...
The third component is a 105.5 millihenry inductor whose leads are connected to
node 6 and node 3 (the circuit's output port). The fourth component is a
nonmodifiable wire (with 0 as its component value) whose leads are connected
to node 0 ...
John R. Koza, Martin A. Keane, Matthew J. Streeter, 2006
10
Inside OrCAD Capture for Windows
By convention, when M is used with resistance values, it always stands for
megohm (for example, 10M is 10 megohm). Inductors are usually in the .1
microhenry to 10 henry range, with millihenry values quite common. By
convention, MH ...
