与 «TENSILE LOAD»相关的英语书籍
在以下的参考文献中发现
tensile load的用法。与
tensile load相关的书籍以及同一来源的简短摘要提供其在 英语文献中的使用情境。
The sudden application of the tensile load may elastically strain the iron lattice at
such a high rate that carbon migration to favored sites cannot occur as the load is
applied. However, if the material remains under load, the time-dependent ...
2
Effects of static
tensile load on the thermal expansion of ...
The effect of static tensile load on the thermal expansion of Gr/PI composite material was measured for seven different laminate configurations.
Gary L. Farley, United States. National Aeronautics and Space Administration. Scientific and Technical Information Branch, Army Research and Technology Laboratories (U.S.). Structures Laboratory, 1981
3
Introduction To Mechanical Engineering:Thermodynamics, ...
If the load is tensile load (pull) it will cause elongation whereas if the load is
compressive load (push) it will result in compression. Similarly, the resisting force
will also depend on the type of loads. The resisting may be tensile or
compressive.
4
Stone: Building Stone, Rock Fill and Armourstone in Construction
Tensile strength. The tensile load required to cause failure of an unconfined
cylindrical specimen of the stone, divided by the cross-sectional area of the
specimen perpendicular to the axis of loading (Fig. C8). The units are, therefore,
force per ...
5
Cabling: The Complete Guide to Copper and Fiber-Optic Networking
These cables must support a bend radius of 25mm (1 ̋) when not subject to a
tensile load. In other words, 25mm (1 ̋) is the minimum bend radius for this
cable type. Inside plant cables with four or fewer fibers intended to be pulled
through ...
Andrew Oliviero, Bill Woodward, 2009
6
Geotextiles Geomembranes and Related Products
The tensile load generated in the geotextile reinforcement due to the application
of a vertical distributed load wt is Pt> - (wy(s-a)Vl + l/6e)/2a (3) where, Ftr is the
tensile load generated in the deflected geotextile, E is the extension of the ...
7
Structural and Stress Analysis
After the concrete has set, the tendons are released and the tensile load in the
tendons is transmitted, as a compressive load, to the concrete. In a post-
tensioned beam, metal tubes or conduits are located in the mould at points where
...
8
Pipeline Design for Installation by Horizontal Directional ...
This susceptibility is attributable to not only HDPE's relatively low tensile yield
strength, but also to the fact that the safe tensile load applicable to HDPE pipe is
time-dependent. An HDPE pipe subjected to excessive tensile load will continue
to ...
American Society of Civil Engineers, 2005
9
Concise Encyclopedia of Composite Materials
Since concrete is weak in tension and will crack under service loads, its tensile
resistance is neglected in design; thus the entire tensile load is carried by the
reinforcement. However, since concrete does have some tensile resistance, it is ...
10
Fracture and Fatigue Control in Structures: Applications of ...
The residual- stress model suggests that the application of a high-tensile-load
cycle forms residual compressive stresses in the vicinity of the crack tip that
reduce the rate of fatigue-crack growth. Finally the crack-closure model
postulates that ...
John M. Barsom, Stanley Theodore Rolfe, 1999
包含词语«TENSILE LOAD»的新条目
找出国内和国际出版社所讨论的内容，以及词语
tensile load在以下新条目的上下文中是如何使用的。
Monitoring the real-time deformation of carbon nanocoils under axial …
A series of three scanning ion microscopy (SIM) images offers visualization of the geometric evolution of the CNC under a tensile load. These images were ... «Phys.Org, 二月 15»
Versatile nano-tensile testing platform available for TEM
The unique "push-to-pull" mechanism transforms the indentation loading into uni-axial tensile loading of the specimen, which is pre-clamped on the device. «nanotechweb.org, 九月 11»
Tabbing composite test specimens: When and why
Many of the testing problems that tabs minimize are independent of the type of loading. Therefore, I'll deal with most of them in a discussion of tensile loading ... «High Performance Composites, 三月 11»
Fiber-matrix interfacial bond test methods
The matrix must be ductile enough to absorb, without fracturing, the energy released when the fiber breaks locally under the applied tensile load (local matrix ... «High Performance Composites, 一月 11»
