与 «오일실»相关的韩语书籍
在以下的参考文献中发现
오일실的用法。与
오일실相关的书籍以及同一来源的简短摘要提供其在 韩语文献中的使用情境。
1
VW Polo Petrol & Diesel Service & Repair Manual: 2002 to 2005
satisfactory seal between the sump and oil seal housing on refitting. b) Unbolt and remove the oil seal housing. c) Working on the bench, lever the oil seal from the housing using a suitable screwdriver Take care not to damage the seal seating ...
2
Direct support and general support maintenance manual: ... - 3-61페이지
( 1 ) Clean up any oil seal grooving on the crankshaft with emery cloth and polish the surfaces with crocus cloth saturated with fuel oil. (2) Replace the front oil seal (13, fig. 3-62) as follows: (a) Remove the oil pump assembly (para 3- 29 b I from ...
United States. Dept. of the Army,
1992
3
Advanced Tribology: Proceedings of CIST2008 & ITS-IFToMM2008
Sealing Performance and Wear Mechanism of PTFE Oil Seal Ye Zibo1, Huang Xing2, Liang Rongguang1 1South China University of Technology Guangdong Guangzhou 510641,China; 2Guangzhou Mechanical Engineering Research ...
Jianbin Luo, Yonggang Meng, Tianmin Shao,
2010
4
VW Volkswagen Transporter T4 Workshop Manual - 24페이지
Special tool for the removal of the camshaft oil seal. The same tool is also used for the front crankshaft oil seal. Fig. 1.35. Special tool applied to the cylinder head to remove the camshaft oil seal. Push against the tool whilst tightening with the ...
Trade Manual, Various,
2013
5
Improving Machinery Reliability - 1권 - 266페이지
50.00 windings 10.00 20.00 bearing 5.00 50.00 oil seal 8.00 10.00 shaft 0.10 0.50 v-belt 20.00 80.00 shaft 0.10 0.50 oil seal 8.00 10.00 bearing 3.00 10.00 oil seal 8.00 10.00 oil seal 8.00 10.00 bearing 5.00 50.00 gearset 8.00 50.00 bearing ...
6
Automotive Engines - 214페이지
Water inlet 8.10 OIL SEAL An oil seal is provided at the rear main bearing for preventing oil leakage through the bearing. Whenever oil leaks from the rear main bearing, the oil seal must be replaced. Many engines use an oil seal with two ...
7
Operator's, organizational, direct support, and general ... - 6-18페이지
BEARING PLATE OIL SEAL a. Removal (fig. 4-7). (1) Remove clutch (114) by loosening set- screw (115). (2) Remove crankshaft bearing plate (117) to replace its oil seal (116). (3) Drive the oil seal out from the inside using bearing plate driver ...
United States. Dept. of the Army,
1992
8
Chilton's Auto Repair Manual, 1993-1997 - 28-51페이지
Apply a coating of wheel bearing grease to the lip of the inner oil seal. 20. If equipped with ABS, be sure to align the hole in the seal to the hole in the steering knuckle for the wheel speed sensor. 21. Install the inner oil seal to the inner side of ...
Chilton Book Company,
1996
9
New JIT, New Management Technology Principle - 74페이지
To be more precise, a total task management team named Drive-Train Oil Seal Quality 5 Team (DOS-Q5) was organized in which the oil seal manufacturer participated. Figure 5.23 is a Relational Chart Method showing the outline of the ...