CO OZNACZA SŁOWO INVAR
Definicja słowa invar w słowniku
stop inwazyjny złożony z 63,8% żelaza, 36% niklu, 0,2% węgla, który jest bardzo małym stopniem rozwoju.
KSIĄŻKI POWIĄZANE ZE SŁOWEM «INVAR»
Poznaj użycie słowa
invar w następujących pozycjach bibliograficznych Książki powiązane ze słowem
invar oraz krótkie ich fragmenty w celu przedstawienia kontekstu użycia w literaturze.
1
Surveying Instruments - Halaman 207
Figure S18 Device for pulling an invar tape / invar tape Figure 519 Stencil for engraving the graduation onto an invar tape Special Rods for Precision Levelling To avoid irregular changes in length, which are possible for wooden rods, invar ...
2
Springer Handbook of Condensed Matter and Materials Data
Table A-.3-25 Thermal expansion coefficient, a and mechanical properties of invar alloys for practical use [3.42] Table A-.3-26 Thermal expansion coeffcient of invar 36 and free-cut invar [3.17] Tabled. 3-27 Some physical properties of invar ...
Werner Martienssen, Hans Warlimont,
2006
3
Concise Encyclopedia of Magnetic and Superconducting ...
The understanding of Invar remained a problem (Wassermann 1990, Wittenauer 1997) before ab initio calculations (Entel et al. 1993) gave basic insights into the relations between lattice structure, atomic volume, and magnetic properties, and ...
4
Fracture Mechanics: Seventeenth Volume : Seventeenth ...
REFERENCE: Soya, I., Takashima, H., and Tanaka, Y., "An Application of Stress Intensity Factor to Fatigue Strength Analysis of Welded Invar Sheet for Cryogenic Use," Fracture Mechanics: Seventeenth Volume, ASTM STP905, J. H. ...
5
Surveying - Jilid 1 - Halaman 44
3.13). A steel tape is a delicate instrument and is very light, and therefore, cannot withstand rough usage. The tape should be wiped clean and dry after using, and should be oiled with a little mineral oil, so that it does not get rusted. Invar Tape.
6
Opto-Mechanical Systems Design, Second Edition, - Halaman 131
Invar and Super-Invar Low-expansion alloys of iron and nickel are used when control of thermally induced dimensional changes is required by the application. One alloy, Invar, contains 36% nickel with small quantities of manganese, silicon, ...
Paul Yoder, Daniel Vukobratovich, Roger A. Paquin,
1992
7
Nickel, Cobalt, and Their Alloys - Halaman 98
Addition of carbon is said to produce instability in Invar, which is attributed to the changing solubility of carbon in the austenitic matrix during heat treatment. Effects of Processing. Heat treatment and cold work change the expansivity of Invar ...
8
Magnetism and Structure in Functional Materials - Halaman 181
Figure 10.3 reveals that there is also an appreciable magnetic contribution to the specific heat in the paramagnetic temperature range for T >T C, which is also maximum in Fe65Ni35 Invar. This excess is very likely caused by FM spin ...
Antoni Planes, Lluís Mañosa, Avadh Saxena,
2010
9
Physics and Engineering Applications of Magnetism - Halaman 173
The problem in Invar or spin glasses is one of the topics which needs to be understood well by researchers in the “intermediate field” in order for them to keep up with the pure and applied physicists. In the following, the problem of the Fe—Ni ...
Yoshikazu Ishikawa, Noboru Miura,
2012
10
Alloying: Understanding the Basics - Halaman 591
Invar has the highest thermoelastic coefficient of all low-expansion iron-nickel alloys, while two alloys with 29 and 45% nickel have a zero thermoelastic coefficient (that is, the modulus of elasticity does not change with temperature). However ...