WHAT DOES PUSH-PULL CIRCUIT MEAN IN ENGLISH?
Definition of push-pull circuit in the English dictionary
The definition of push-pull circuit in the dictionary is a circuit using two similar electronic devices, such as matched valves, made to operate 180° out of phase with each other.
10 ENGLISH BOOKS RELATING TO «PUSH-PULL CIRCUIT»
Discover the use of
push-pull circuit in the following bibliographical selection. Books relating to
push-pull circuit and brief extracts from same to provide context of its use in English literature.
1
The Path to Athletic Power: The Model Conditioning Program ...
The Hammer Strength push-pull circuit trains the core in a functional way with the
body standing in an upright position. Unlike sit-ups or core exercises with the
pelvis stabilized by the ground, the push-pull exercises require the core muscles
to ...
2
The Amp Book: A Guitarist's Introductory Guide to Tube ...
Push-pull circuit operation is as follows: The secondary winding of input
transformers is tapped at its center. This center wire is routed to the cathode of
the tubes, usually through a resistor and capacitor. The outer ends of the
secondary are ...
3
A FIRST COURSE IN ELECTRONICS
11.8 Show that the maximum conversion efficiency of the idealized Class B push-
pull circuit is 78.5%. 11.9 Draw the circuit of a Class B push-pull power amplifier
and demonstrate that even harmonics are eliminated in a balanced circuit.
ANWAR A. KHAN, KANCHAN K. DEY, 2006
4
Analog And Digital Electronics
2.9 Push Pull Class B Amplifier The push pull circuit requires two transformers,
one as input transformer called driver transformer and the other to connect the
load called output transformer. The input signal is applied to the primary of the
driver ...
U.A.Bakshi, A.P.Godse, 2009
The circuit arrangement of the complementary push-pull circuit is shown in Figure
2.16. Note that the complementary symmetry circuit requires two power supplies
namely VCcl and VCCZ . Push-pull amplifiers means the two transistors are ...
Balwinder Singh, Ashish Dixit, 2007
6
Electronic Circuits and Appliations
Class. B. Amplifier. The push pull circuit requires two transformers, one as input
transformer called driver transformer and the other to connect the load called
output transformer. The input signal is applied to the primary of the driver
transformer.
A.P.Godse, U.A.Bakshi, 2009
push-pull. amplifier. Figure 5.6 is a practical sample push-pull circuit. If R2 is zero
ohms then the circuit operates in class B push-pull mode. Suitable non-zero
value of R2 should be used for class AB push-pull mode of operation. Here in Fig
.
A. KANDASWAMY, ANDRÉ PITTET, 2009
The push-pull circuit of Figure 2-2 includes an input transformer, T1, that applies
the signal to the two transistors so that they are driven 180 degrees out-of-phase.
Output transformer T2 combines the output powers of the two transistors.
9
Basic Electronics and Linear Circuits
The use of input transformer is thus eliminated. The use of output transformer can
also be eliminated by a circuit called complementary-symmetry circuit. This is
explained in the next section. 10.8.4 Complementary-Symmetry Push-pull Circuit
It ...
N. N. Bhargava, N. N. Bhargava S. C. Gupta D. C. Kulshreshtha, 1984
Class. B. Amplifier. The push pull circuit requires two transformers, one as input
transformer called driver transformer and the other to connect the load called
output transformer. The input signal is applied to the primary of the driver
transformer.
U.A.Bakshi A.P.Godse, 2008
4 NEWS ITEMS WHICH INCLUDE THE TERM «PUSH-PULL CIRCUIT»
Find out what the national and international press are talking about and how the term
push-pull circuit is used in the context of the following news items.
WNAMM13: Blackstar In White
While the preamp uses a traditional 12AX7 tube, the power section uses the dual-triode 12BH7 tube wired in a push-pull circuit. Blackstar says that this ... «Sonic State, Jan 13»
M/A-COM Tech launches push-pull CATV amplifier with low …
Using the firm's established 0.5µm MESFET process, the device is designed for integration in a 75Ω push-pull circuit and exhibits low distortion. “With the ... «Semiconductor Today, Aug 12»
Manley Labs Reference 240 monoblock power amplifier
This transformer design, coupled with Manley's use of a double driver tube for each phase of the push-pull circuit, makes the Reference 240 a true differential ... «Stereophile Magazine, Sep 09»
Marantz SM-11S1 Reference power amplifier
The SA3, the latest iteration of Marantz's High Definition Amplifier Module (HDAM) complementary cascade push-pull circuit, is a compact arrangement ... «Stereophile Magazine, May 08»