CĂRȚI ÎN ENGLEZĂ ÎN LEGĂTURĂ CU «OILHOLE»
Descoperă întrebuințarea
oilhole în următoarea selecție bibliografică. Cărți în legătură cu
oilhole și extrase din aceasta pentru a furniza contextul de întrebuințare al acestuia în literatura Engleză.
1
Crane-shovel: Power Unit, Revolving Truck Mounted, Pneumatic ...
(4) Place a new gasket (3) over studs (15) on rear end of the crankcase, being
sure the oilhole in the gasket lines up with the oilhole in the crankcase. Install the
oil seal ring (2) in the end cover (1). Install the end cover on the studs, being sure
...
2
Operator, Organizational, Field and Depot Maintenance ...
Place the proper connecting rod (8) in the matched piston so that the stamped
arrow on top of the piston faces the side of the connecting rod opposite the
oilhole in the connecting-rod cap. Tap the piston pin into the other bore of the
piston, and ...
3
Sensors and controls for manufacturing -- 1988: presented at ...
6 Photograph of the Data Acquisition System for indirect Sensing of Drill Wear 4-
2 Training Process The percent increase of peak-to-peak amplitude for vertical
acceleration (Xt) was 132Z-151Z when the next-to-last oilhole was drilled; it was
...
E. Kannatey-Asibu, A. G. Ulsoy, Yoram Koren,
1988
4
Materials and Process Selection for Engineering Design, ...
... changed: • The dowels and bolt holes have the same diameter. • The center of
the bore has a larger diameter than the ends to reduce the length to be machined
. This will also eliminate the necessity to the exit burr at the end of the oilhole.
5
Direct Support, General Support, and Depot Maintenance ...
NOTE There is an oilhole in the bottom of the cam follower. Install the cam
follower with the oilhole pointing away from the valve, so that the hole is not
covered by the follower guide. (4) With the cam follower rollers (29) pointing
across the ...
6
Operator and Organizational Maintenance Manual: ...
(2) Place 2 drops of oil (PL-Special) on each door hinge and door catch of
Instrument Shelter, Meteorological S-101/U. (3) Support ML-54 requires 1 drop of
oil (PL-Special) in the oilhole of the long carrier and in the slot of the short carrier.
Put oil on the wool in the oilhole under the shuttle slide plate of long-bobbin
machines with such a hole. Some long-shuttle machines have a block of felt or
ball of wool so set against the front end of the shuttle race that the point of the
shuttle ...
8
Organizational, DS, GS, and Depot Maintenance Manual ...
Apply 1 or 2 drops of Lubricating Oil, General Purpose, Preservative (PL Special)
(FSN 9150- 273-2389), to the oilhole in each reel bearing and to the oilhole in
the reel crank handle. 10 AGO 7365A 4—1. Scope of Organizational
Maintenance ...
9
Operator's, Organizational, Direct Support, and General ...
Note the oilhole in the bottom of the cam follower. With the oilhole directed away
from the exhaust valves, slide the cam follower in position in the cylinder head. 2.
Assemble the serrated lower spring seat, spring, and upper cup- shaped spring ...
10
Boundary Elements and Other Mesh Reduction Methods XXXVI:
The stress concentration always appears near the oilhole, so it cannot be ignored
during the CAE analysis. Mesh generated by the presented method contains 44
hexahedral WIT Transactions on Modelling and Simulation, Vol 56, © 2013 WIT ...
X. W. Gao, A. H-D. Cheng, C. A. Brebbia,
2013