ETIMOLOGIA CUVÂNTULUI WOODRUFF KEY
Named after the Woodruff Manufacturing Co, in Hartford, Connecticut, who first manufactured it in 1892.
CĂRȚI ÎN ENGLEZĂ ÎN LEGĂTURĂ CU «WOODRUFF KEY»
Descoperă întrebuințarea
Woodruff key în următoarea selecție bibliografică. Cărți în legătură cu
Woodruff key și extrase din aceasta pentru a furniza contextul de întrebuințare al acestuia în literatura Engleză.
1
Design of Machine Elements
9.20 Feather Key 9.12 WOODRUFF KEY A Woodruff key is a sunk key in the form
of an almost semicircular disk of uniform thickness as shown in Fig. 9.21. The
keyway in the shaft is in the form of a semicircular recess with the same Woodruff
...
2
Basic Mechanical Engineering
It is alternative to splined connection. iv) Woodruff key : A woodruff key is a sunk
key, in the form of an almost semi-circular disc of uniform thickness, as shown in
Fig. 9.10. The key way in the shaft is in the form of a semi-circular recess with the
...
A.A.Karad, D.D.Shinde,
2009
3
Manual of Engineering Drawing: Technical Product ...
19.11), is a segment of a circular disc and fits into a circular recess in the shaft
which is machined by a Woodruff key way cutter. The shaft may be parallel or
tapered (Figs 19.12 and 19.13) showing the method of dimensioning shafts for ...
Colin H. Simmons, Dennis E. Maguire,
2012
4
Developing Solid Oral Dosage Forms: Pharmaceutical Theory & ...
Keys fitted to the upper punches are available in two configurations: (1) the
standard Woodruff key, sometimes referred to as the pressed-in key, and (2) the
feather or flat key, often referred as the European key. The Woodruff key, often
referred ...
Yihong Qiu, Yisheng Chen, Geoff G.Z. Zhang,
2009
There are many kinds of keys. The five major kinds used in industry today are
illustrated in Figure 13-37: square key, flat key, gib head key, Pratt & Whitney key,
and Woodruff key. Where a lot of torque is present, a double key and keyseat are
...
6
Direct Support and General Support Maintenance for ...
NOMENCLATURE PART NUMBER NATIONAL/NATO STOCK NUMBER 283
Woodruff Key 8327443 5315-00-281-7650 284 Woodruff Key 7409197 285
Woodruff Key MS35756-13 5315-00-616-5521 286 Woodruff Key MS35756-15 ...
7
Analysis and Design of Machine Elements
()22n. If there are two keys (n = 2) as shown in figure l = 0.55d p d ...(9.11). 9.5.
DESIGN. OF. WOODRUFF. KEY. The Woodruff key goes deeper into the shaft as
compared to the depth into the hub. Generally, radial clearance of 2 mm is ...
Vijay Kumar Jadon, Suresh Verma,
2010
8
Clymer Polaris, Sportsman 400, 2001-2003, Sportsman 500, ...
Check the Woodruff key and the crankshaft key slot for wear or damage. Replace
the Woodruff key if necessary. 8. Check the Woodruff key slot in the drive
sprocket for wear or damage. 9. Inspect the rear tensioner slider (Figure 160) for
wear ...
Ed Scott, Clymer Publications,
2004
TABLE 13.2 PROPORTIONS FOR SPLINED SHAFTS OF VARIOUS SIZES
Woodruff Keys A Woodruff key is a particular kind of sunk key in which the key is
a part of a segment of a circular disc of uniform thickness. Thus the width of the
key is ...
10
Introduction to Machine Design
The bottom portion of the Woodruff key fits into circular keyway in the Fig. 4.21
Woodruff key shaft. The keyway in the hub is made in usual manner. The
projecting part of Woodruff key fits in the keyway in the hub. Once placed in
position, the ...